Superior Fireplaces WRT4820, Инструкция по установке и эксплуатации

Страница: 2 / 32

TABLE OF CONTENTS
Introduction ......................................Page 2
Parts Required .................................Page 2
Optional Equipment ...........................Page 2
SAFETY RULES and Specifications for
Mobile or Manufactured
Home Installation .........................Page 3
Operating The Fireplace ....................Page 4
Fuel ...................................................Page 4
Combustion Control .........................Page 4
Refueling For Best Performance .......Page 5
Smoking – Causes And
Troubleshooting ............................Page 5
Important Cautions ...........................Page 5
Maintaining Your
WRT4820WS Fireplace ................Page 6
Chimney Maintenance .......................Page 6
Dealing With A Chimney Fire .............Page 6
Finish Door Casing Care ....................Page 6
Disposing of Ashes ...........................Page 6
Refractory Installation .......................Page 7
Door Installation ...............................Page 7
Door Adjustment ...............................Page 7
Glass Care - Replacement .................Page 8
Glass Care - Cleaning ........................Page 8
Gasket Replacement ........................Page 8
Fireplace Installation ........................Page 8
Locating The WRT4820WS Fireplace...Page 8
Installing The Finishing Kits ..............Page 9
Framing, Facing And Mantel ..............Page 10
Hearth Extension Requirements .......Page 10
Cold Climate Installations ..................Page 10
Fireplace and Framing Dimensions ...Page 11
Insulated Chase Construction ...........Page 12
Nailing Flanges ..................................Page 12
Facing / Mantel ..................................Page 13
Hot Air Ducting Installation ..............Page 14
Gravity Kit .........................................Page 14
Central Forced Air Kit ........................Page 15
Outside Air Kit ..................................Page 16
Chimney System ...............................Page 17
Chimney Installation Notes ...............Page 17
Chimney Installation Instructions ......Page 18
Offset Chimney Installation ...............Page 19
Angled Wall Radiation Shield ............Page 21
Chimney Support Installation ............Page 22
Chimney Chase And
Multiple Terminations......................Page 22
Chimney Adaptor ..............................Page 22
Masonry Application Instructions .....Page 23
Installation Accessories ....................Page 24
Replacement Parts ............................Page 25
Specifications ....................................Page 25
Clearances to Combustibles ..............Page 25
Chimney Components Lists ..............Page 27
Safety/Listing Label ...........................Page 29
Warranty ...........................................Page 31
Product Reference Information .........Page 32
THE FIREPLACE
INTRODUCTION
The WRT4820WS wood-burning fireplace is
an energy efficient, heat circulating, closed
combustion fireplace. You will receive a lifetime
of comfort and enjoyment from your fireplace
provided it is installed, maintained and oper-
ated properly.
•
Please read these instructions and retain
this manual for future reference.
•
Before beginning the fireplace installation,
consult the local authorities to obtain your
building permit and check your local building
codes. Install the fireplace only as described
in these instructions and using only IHP
components.
• This fireplace has been tested for CAN/ULC
S610-M87 and ANSI/UL 127 under report
number 3011202. It has also been tested
for EPA 40 C.F.R Part 60, section 60.532(b).
Certificate number 537.
•
The WRT4820WS fireplace is not intended for
use with a gas log set. Do not use a fireplace
insert or any other product with this fireplace
unless it is specified by IHP for use with this
appliance. Failure to follow these instructions
will void the certification and the warranty of
the fireplace and may result in an unsafe
installation.
• IHP wood fireplaces are designed for use as
a supplemental heater. They are not intended
for continuous use as a primary heat source.
PARTS REQUIRED
Fireplace Model WRT4820WS
• . Finishing Kit - Required *
... (Order Separately)
- Louver kit
OR
- Clean face obstruction plate kit. Must be
used in conjunction with a gravity vent kit.
*SEE “INSTALLING THE FINISHING KITS”
SECTION FOR THE ASSEMBLY OF THE FIN-
ISHING KITS.
• . Black steel door - Required
... (included w/fireplace)
• . Outside air kit - Required
... (included w/fireplace)
• . Blower kit with thermo-disc (V2)
... (included w/fireplace)
• 6” diameter chimney
*
- model ASHT+,
S-2100+, , or AC manufac-
tured by Security Chimneys
®
only, including:
- Chimney lengths
- Elbows (where necessary)
- Associated components as per these
installation instructions
• 6” diameter chimney
**
- Model DuraTech
®
DTC manufactured by DuraVent
®
only,
including:
- Chimney lengths
- Elbows (where necessary)
- Associated components as per these
installation instructions
OPTIONAL EQUIPMENT
• Additional Equipment (optional)
- AC chimney adaptor
*
(required if using AC chimney)
- AC chimney outside air kit
- Gravity venting system
- Central forced air kit
u
- Blower speed control
- Rigid Firescreen
u
u Not tested under EPA certification. If
installed, this appliance no longer quali-
fies for EPA certification. Check with local
authorities having jurisdiction for require-
ments in your area.
CONGRATULATIONS!
When you purchased your new wood fireplace, you joined the ranks of thousands of
individuals whose answer to their home heating needs reflects their concern for aesthetics,
efficiency and our environment. We extend our continued support to help you achieve
the maximum benefit and enjoyment available from your new wood fireplace.
Thank you for selecting a IHP wood fireplace as the answer to your home supplemental
heating needs.
**
Available from DuraVent
®
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2
* Available from Security Chimneys
®