background image

The duct system must be installed respecting 

the following:

1. Remove the plates closing up the 8” dia. 

holes on top of the fireplace.  Then, cut 

the insulation and remove the plate under 

the insulation in order to obtain two 8” dia. 

openings.  Fix the adaptors on the fireplace 

openings by turning clockwise (

Figure 20)

.

2. Maintain at least a 2” (50 mm) clearance 

between the ducts and any combustible 

material; the required hole size is 13”  x  13” 

(330 mm x 330 mm).

  Exception #1:  For the grills, the fram-

ing can be 10-3/4” x 10-3/4” (275 mm 

x 275 mm) to provide the clearance as 

required by the integral spacers on the 

double outlet duct system.

3. The maximum number of elbows in a run 

of duct is two.

4.  Maintain at least 6-1/2” (160 mm) clearance 

from the outlet grill framing to a combustible 

ceiling, side wall or mantel.

5.  When traversing a combustible wall or floor, 

a firestop must be installed at the wall or 

floor penetration.  The hole size must be 

13” X 13” (330 mm x 330 mm).

6.  Do not connect the hot air ducts to a central 

heating system.  Malfunction of the heating 

system’s blower will cause the fireplace to 

overheat.  A furnace duct is only single wall 

and not double wall as is required for the 

WRT4820WS fireplace hot air exhaust.  

7. Use only IHP grills and components as 

described in this manual. Other grills or 

registers, for example, may be too restrictive 

and may overheat the fireplace or ceiling.

8. Do not use insulated flexible ducts as they 

will overheat.

9. Do not use tees or any other components 

than the ones specifically listed here.

10. Never allow the ducting to pitch down as 

hot air will be trapped creating a fire hazard.  

Never route the ducting downwards

.

11. The hot air outlet grills must be installed with 

the louvers pointing downwards in order to 

prevent overheating adjacent ceilings.

12. Always install the two outlet grills when using 

the double hot air outlet kit and blocking the 

upper louver of the fireplace.

CENTRAL FORCED AIR KIT (NOT TESTED 
UNDER EPA CERTIFICATION)

The knock-outs provided on the back and on 

the sides of the WRT4820WS fireplace allow 

the connection of insulated flexible pipe which 

enables you to heat adjacent rooms up to 50 

feet from the fireplace.

The ducting system must be installed as de-

scribed below:

A) Remove the knock-out and cut the insulation. 

In the back, there may be another knock-out 

to remove under the insulation.

B) Fix the adaptor at the back and/or the side 

of the fireplace by twist-locking the adaptor 

to the fireplace. You can use more than one 

outlet on the fireplace 

(Figure 23)

.

C) Attach the 5” flexible pipe, using the collars 

provided. Important: Make sure that the 

plastic wrapping around the flexible pipe 

will not be in contact with the fireplace using 

aluminum tape.

D)  Route the flexible pipe to the chosen location. 

The ducting system can be installed either 

in an upper room or in a lower room.

E) Attach the flexible pipe to the fan, using the 

collars 

(Figure 24)

.

F)  Fix the back draft damper to the fan outlet.

G)  Attach a flexible pipe to the fan / flexible pipe 

adaptor (square to round) and stretch it up 

to the location where the heat is required.

H) At that point, the flexible pipe can be attached 

to any air distribution grill. 

I) Install the blower heating and cooling ther-

mostat (HCTW) in that part of the house to 

be heated by the hot air duct. The thermostat 

can be switched to a cooling thermostat and 

installed in the same room as the unit. This 

thermostat will turn on the blower when 

the room where the fireplace is located 

becomes too hot.

This option requires electricity. Make sure that 

the connections to the fan have been made 

according to the local codes and comply with 

their requirements (see instruction provided 

with the thermostat).

Figure 23

Figure 24

Adaptor

Insulation

Blower

Tightening Collar

Aluminium Tape

Flex 5” Diameter

Insulated

Flexible

pipe

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

15

Содержание WRT4820

































Отзывы: