manualshive.com logo in svg

Suntek 247 BP+VITALS, Руководство пользователя

Поделиться
Скачать
Suntek 247 BP+VITALS Скачать руководство пользователя страница 47

 

 

   

 

 

35 

 

1.

 

Remove the Temperature Well from the Temperature Module. 

2.

 

Replace the Temperature Probe with the Calibration Plug. 

3.

 

Replace the Temperature Well. 

4.

 

Initiate a measurement by inserting and removing the Temperature probe from the 
well. 

5.

 

Verify the accuracy of the measurement. 

 

Probe accuracy can be checked by using the thermometer as you would on a patient in any 
mode with a cover, but place it in a calibrated water bath.  Direct mode is accurate to +/- 0.1 
C of the calibrated water bath temperature.  Predictive mode accuracy is accurate to +/- 0.2 C 
of the calibrated water bath temperature. 

Replacing the Rechargeable Battery

 

Replace the battery:  

 

According to your regular maintenance schedule. 

 

When the battery no longer charges. 

 

After heavy use, if necessary. 

 
To replace the battery: 

1.

 

Remove the four screws securing the battery bay door. 

2.

 

Carefully remove the battery from the battery bay, being careful not to pull on 
the wires attached to the battery terminals. 

3.

 

Disconnect the wires from the battery terminals. 

4.

 

The rechargeable battery contains lead.  Please dispose of the old battery properly. 

5.

 

Connect the wires to the terminals of the replacement battery, ensuring the red 
wire is attached to the red terminal and the black wire to the black terminal.  If 
the wires are reversed, no damage will occur, however the 

SunTech 247

 will not 

operate.  Be sure to use 

SunTech

 part number 17-0014-00 for the replacement 

battery in order to maintain optimum performance. 

6.

 

Re-secure the battery bay door with the four screws removed in step 1. 

7.

 

Connect the power supply to turn the device on and charge the replacement 
battery fully before using. 

 

 

 

If the rechargeable battery is disconnected for any reason, the device must 
be connected to AC mains power via the power supply before the unit will 
turn on; this is required even if the battery has been properly reconnected.  

Disposal 

This symbol indicates the device contains materials (such as electrical components) 
which are hazardous. Please return to 

SunTech Medical

 for disposal. 

Содержание 247 BP+VITALS















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды