Stratasys Objet1000 Connex 2 Скачать руководство пользователя страница 148

Страница: 148 / 174

Operating & Maintaining the Objet1000 - Connex 2 3D Printer

6–28

DOC-06800 Rev. A

5. Lift the suction tube to secure it in a raised position.

6. Remove the two screws securing the covering of the roller waste

collector and remove it.

Figure 6-30: Removing the roller waste collector covering

7. Remove the covering by pulling it out, and then lower it.

8. Clean the roller waste collector and the scraper blade surface using

cotton swabs. Make sure to remove any remaining printing materials.

Figure 6-31: Cleaning the roller waste collector

To check the effectiveness of the roller scraper:

1. Put on the cleaning gloves.

2. Wet a cloth with isopropanol.

3. Use the cloth to wet the bottom of the roller.

4. Turn the roller slowly with your hand. As the blade scrapes the roller,

make sure the isopropanol is spread evenly over the entire length of
the blade.

5. Inspect the roller. If it is not dry, replace the blade. (See Replacing the

Roller Scraper on page 6 29.)

Be very careful to save the covering screws. These are special screws; if
they are lost you need to order replacements.

Roller waste
collector screws

Before replacing the covering you can check the effectiveness of the roller
scraper

see below.

D R A F T
16 June 2013

Содержание Objet1000 Connex 2















































































































































































Результаты поиска

Содержание Objet1000 Connex 2

Отзывы:

Stratasys Objet1000 Connex 2, Руководство пользователя, Страница: 148 / 174

Результаты поиска

Содержание Objet1000 Connex 2

Отзывы: