Stratasys Objet1000 Connex 2 Скачать руководство пользователя страница 14

Страница: 14 / 174

Safety

2–2

DOC-06800 Rev. A

Safety Features

Objet 3D printers are designed to comply with CE and FCC standards.
They are equipped with the following safety features:

Figure 2-1: Objet1000—front view

Figure 2-2: Emergency Stop Switch—Push to stop motors, turn to release

Interlock Switch

The power supplied to the UV lamp and the

motion motors is turned off when the doors are

opened.

WARNING: Do not defeat (override) the

interlock switch. Doing so could result in

serious personal injury.

If the interlock switch

does not function correctly, do not use the

printer, and contact your service provider.

Safety Lock

The doors are locked while the printer is

working. The lock is released when the printer

reverts to

pause

stop

mode.

WARNING: Do not defeat (override) the

safety lock. Doing so could result in serious

personal injury.

If the safety lock does not function correctly, do

not use the printer, and contact your service

provider.

UV Screening

The transparent section of the doors blocks

harmful UV radiation, allowing the operator to

view the model as it is being made.

Circuit Breaker

The power to the printer is turned off in case of

electrical overcurrent.

Note: The circuit breaker is only accessible to
service personnel.

Grounded Chassis

The chassis of the printer is grounded, to

prevent electrical shock.

Note: The power outlet must be properly
grounded, in accordance with the local
electric code, to provide this protection.

Emergency Stop

Emergency stop switches are located on the

front and back of the printer.

Important: Pushing the emergency stop
switch disconnects power to motors only.
It does not disconnect the power supply to
the printer; printer circuits remain on.

D R A F T
16 June 2013

Содержание Objet1000 Connex 2















































































































































































Результаты поиска

Содержание Objet1000 Connex 2

Отзывы:

Stratasys Objet1000 Connex 2, Руководство пользователя, Страница: 14 / 174

Результаты поиска

Содержание Objet1000 Connex 2

Отзывы: