STOP&GO 7 PLUS-MINUS CLIP, Руководство по установке

Страница: 6 / 31

EN EN
10 11
After installing the control device including the speaker housing, laying the high-voltage cable and attaching the stainless
steel contact plates, the setup should be retested to ensure that it functions correctly. Since the integrated sensor auto-
matically switches off the device if the vehicle is in use, you must ensure that the car is motionless before performing a
function check using a multimeter. Set “direct current – 300 V” and measure the voltage between the two stainless steel
contact plates (should read 250–300 V). If the function check is successful but voltage fails to build up after installation,
an installation error has occurred.
Blinking at regular intervals (approx. every 5 seconds) = OK: ultrasound is being emitted, high voltage has built up.
Fast blinking = voltage is building up/dissipating. Caution: residual voltage!
LED off = device is switched off.
1. Is the operating voltage (12 V plus and minus) of the car battery also present at the unit connections?
2. Is the engine switched off?
3. Have all the plus stainless steel contact plates been installed so that they do not touch any other live or
earthed parts (risk of short circuit)?
4. Is the device completely still and not subject to any movement or vibration?
5. Has the position of the stainless steel contact plates on the cable been changed, damaging the copper core?
Prior to
installation
Installation
Function
check
Trouble
shooting
Circuit
diagram
Warranty
Prior to
installation
Installation
Function
check
Trouble
shooting
Circuit
diagram
Warranty
Prior to
installation
Installation
Function
check
Trouble
shooting
Circuit
diagram
Warranty
07553
off
on
ST
OP&GO
ST
OP&GO
ST
OP&GO
ST
OP&GO
ST
OP&GO
Speaker housing
Function control light
Control device/slide contact*
*Switching the device on and off
Pull the slide contact (printed part)
half way out.
Fuse box
12 V (–) earth
12 V (+)
0.5 A F
Minus plate
Base
Fastening tunnell
Plus plate
(marked with a sticker)
Fastening tunnell
Cable wall
Guide steps
Hinge
Slide out pin with suitable
device to open the hinge
IMPORTANT! Terms of the warranty (please keep in a safe place)!
Our 7 PLUS-MINUS CLIP High-voltage device with ultrasound comes with a 48-month functional warranty.
1. Any reasonable complaints within the warranty period from the date of purchase will be remedied free of charge,
either through repair or delivery of a replacement product at our discretion. In order for the warranty to apply,
our product must have been properly installed and maintained in accordance with our installation instructions.
2. To enable us respond to problems, please return the control device and installation invoice to us, initially at your
own expense.
3. Installation and removal costs will only be covered by us in the event that the device is proven to be defective.
Any claim under Section 5 of our General Terms and Conditions shall remain unaffected, subject to the condi-
tions set out therein.
4. Any damage caused by improper installation or incorrect, negligent or forceful operation shall invalidate the
warranty. There shall be no liability for consequential damage.
Technical changes and errors excepted.
Please fill in to claim against the warranty: For warranty claims to be processed, you must send us the filled in coupon
and the garage/installation invoice!
Garage stamp Unit serial number
Date of purchase
Technical support
+49 (0) 7631 9727-80
Development and Sales
Norbert Schaub GmbH
Robert-Koch-Straße 20
79395 Neuenburg am Rhein
GERMANY
Tel. +49 (0) 7631 9727- 0
Fax +49 (0) 7631 9727-27
service@stop-go.de
www.stop-go.de/en
Prior to
installation
Installation
Function
check
Trouble
shooting
Circuit
diagram
Warranty