manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Руководство по конфигурации и эксплуатации, Страница: 81 / 158

Поделиться
Скачать
Stock DISOCONT Tersus DT-9 Скачать руководство пользователя страница 81

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

79 

P 07.04 DI: Source Belt Sensor 

Default: n/a (Hidden) 

Options: 

n/a (not used) 
DI 13 – High/Low 

 
Normally Hidden 
 
This parameter is used to specify the digital input used for the belt slip sensor.  The slip sensor is 
connected to a driven roller and generates a frequency input proportional to the belt speed.  This 
value is compared to the tachometer signal from the motor to detect belt slippage at the head pulley.  
See also: parameters P 07.08 Event: Belt Slip and P 07.09 DO: Belt Slip. 
 
This parameter is normally set to n/a. 
 
 

P 07.05  BIC Active

 

Default: NO  (Hidden)

 

Options:

 

NO 
YES  

 

 
Normally Hidden 
 
This parameter is used to activate the moisture Belt Influence Compensation (BIC) system.  The BIC 
system is used in batching feeders to tare individual sections of the belt separately so that batches 
that are less then a full belt length are weighted accurately. 
 
The BIC feature is not used in continuous feeding systems and this parameter should always be set 
to NO. 
 
 

P 07.06 DI: BIC freeze 

Default: n/a (Hidden) 

Options: 

n/a (not used) 
DI 1 thru DI 14 – High/Low 

 
Normally Hidden 
 
This parameter is used specify a digital input that is used to freeze the tare value while the BIC 
feature is active. 
 
This parameter is normally set to n/a. 
 
 

P 07.07  Slip Value

 

Default: 10.0 %  LB (Hidden) 

Min: 0.0 % 

Max: 20.0 % 

 
Normally Hidden 
 
This parameter specifies the maximum amount that the belt speed measured by the belt slip input 
can differ from belt speed measured by the tachometer input, without generating an error. 
 
This parameter is normally set to 10.0 % LB. 
 
 

Содержание DISOCONT Tersus DT-9































































































































































Отзывы:

Нет отзывов