manualshive.com logo in svg

Stock DISOCONT Tersus DT-9, Руководство по конфигурации и эксплуатации, Страница: 66 / 158

Поделиться
Скачать
Stock DISOCONT Tersus DT-9 Скачать руководство пользователя страница 66

DISOCONT® Tersus (DT-9) Configuration and Operations Manual 

©Schenck Process Group 

64 

9.2.3 Parameter Group 03 - Control Sources 

 
This parameter group is used to select the control sources for use during Remote mode operation. 
 
 

P 03.01 Feeder Start 

Default: DI 2 – High (Hidden) 

Options: 

NO (not used) 
DI 1 thru DI 14 – High/Low 

 
Normally Hidden 
 
This parameter selects the digital input used as the feeder start command. 
 

Caution:

 This is a static input! Switching to remote control mode with the start input activated will 

start the feeder. 
 
This parameter is normally set to DI 2 – High (terminal block X1-4) and is connected to wire 112. 
 
 

P 03.02  Feedrate Setpoint

 

Default: AI 1 

Options: 

OP (Operator Panel) 
FB (Field Bus) 
R-L (Raise/Lower Contacts) 
AI (Analog input) 

 
This parameter selects the source for the feedrate demand signal and can be set to the             
following values: 
 
AI 1 for use with an analog (usually 4-20mA) input signal on SIG+ and SIG- 
R-L for use with the Raise/Lower input signals (See  P03.07 and  P03.08) 
OP for use with EasyServe 
FB or remote control using a Field Bus 
 
This parameter is normally set to AI 1 and is connected to wires Sig+ and Sig-. 
 
 

P 03.03  Setpoint Range

 

Default: 20.00 mA 

Min: 0.00 mA 

Max: 1000.00 mA 

 
This parameter determines the nominal 100% signal level for the analog input channel. It should be 
set to 20.0 for a 0-20mA, 4-20mA or 0-10V input.  
 
This parameter is normally set to 20.00 mA and is only active when P03.02 is set to an analog      
input signal. 
 

Note: 

When an analog input card is used, the input jumper must be set toward the outside of the card 

for a voltage input signal and toward the middle of the card for a current input signal. 
 
 

Содержание DISOCONT Tersus DT-9































































































































































Отзывы:

Нет отзывов