Stober SC6 Series Скачать руководство пользователя страница 29

Страница: 29 / 96

STOBER

7 | Commissioning

02/2020 | ID 443025.06

Limiting torque/force (optional)

The specified default values take into account the rated operation together with the overload reserves.

Select the

Axis model

wizard >

Limit: Torque/force

If the motor force must be limited, adapt the saved values.

7.1.5

Synchronizing EtherCAT nodes

Precise

synchronisation

of the EtherCAT nodes is absolutely required for spatially distributed processes that require

simultaneous actions (path interpolation). EtherCAT provides the distributed clocks (

DC-Sync

) method for this.

Synchronization using distributed clocks is more precise when compared to the SyncManager event synchronization
(

SM-Sync

) because it is subject to fewer fluctuations. For this reason, DC-Sync is pre-configured in EtherCAT masters and

slaves.

PLL synchronization wizard

Leave the default settings in the first step and optimize them if necessary once you have started up the EtherCAT network
and can assess and evaluate the quality of communication.

More detailed information on synchronization and how you can adjust it after the fact can be found in the chapter

Synchronization [

}

58]

Содержание SC6 Series

































































































Результаты поиска

Содержание SC6 Series

Отзывы:

Бренды по названию

Популярные бренды

Stober SC6 Series, Руководство по эксплуатации

Результаты поиска

Содержание SC6 Series

Отзывы:

Бренды по названию

Популярные бренды