Stihl FS 40 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 82

background image

62

Series 4144 Components FC, FS, KM

– Open the tank cap.

:

Use hook (2) 5910 893 8800 to
remove the pickup body (1) from
the fuel tank.

Do not overstretch the fuel hose.

– Check the pickup body (1) and

replace if necessary

– Reassemble in the reverse

sequence.

8.9.2

Fuel Hoses

In order to guarantee tightness of
the fuel system, the fuel hoses must
be pushed firmly and fully on to the
stubs – always install new fuel
hoses after every repair.

To avoid damage to the fuel hoses
and stubs, fit the hoses by hand.

Do not use pointed or sharp-edged
tools and do not cut open the fuel
hoses at the stubs because they
could be damaged in this way.

1

545RA219 TG

2

To aid assembly, use STIHL press
fluid at the points recommended. Do
not use any other oil, fuel, grease or
press fluids since they may damage
the fuel hoses.

– Remove the pickup body,

– Remove the spacer flange,

:

Pull the fuel return hose (1) off
the stub.

:

Pull the fuel suction hose (1) out
of its seat.

1

545RA220 TG

1

545RA221 TG

– Always install new fuel hoses.

:

Push the new fuel suction hose
(1) through the hole (arrow) in the
fuel tank.

– Coat the grommet on the new

fuel suction hose with STIHL
press fluid,

545RA222 TG

1

545RA223 TG

«
...
61
62
63
64
65
...
»

Содержание FS 40



















































































Отзывы:

Нет отзывов

Похожие инструкции для FS 40

Бренд: SYSFORM Страницы: 7

Бренд: Panasonic Страницы: 6

EY3502 - CORDLESS METAL SAW

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 17

EY3552 - 18V METAL SAW

Бренд: Panasonic Страницы: 124

Бренд: Panasonic Страницы: 176

Бренд: Tregaskiss Страницы: 24

Бренд: Fein Страницы: 77

FoamWerks WA-8001

Бренд: Logan Graphic Products Страницы: 2

STIGA PARK 125 COMBI PRO

Бренд: Stiga Страницы: 10

SuperLine Series

Бренд: Kaufmann Страницы: 8

Бренд: RASOR Страницы: 16

Бренд: Ryobi Страницы: 148

Бренд: Dyna Страницы: 9

Бренд: MADER Страницы: 64

Бренд: RAIMONDI Страницы: 32

Бренд: Far Tools Страницы: 49

Бренд: Baier Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды