Stihl FS 40 Скачать руководство пользователя страница 18

Страница: 18 / 82

Series 4144 Components FC, FS, KM

Line up the air baffle (1).

The air baffle's slot must engage the
engine housing rib (arrow) at both
sides.

– Turn the machine over.

Insert screws (arrows) and
tighten them down firmly.

– Turn the machine over

545RA038 TG

545RA039 TG

– Coat stubs (arrows) and ends of

hoses with STIHL press fluid,

Install new fuel return hose (1)
and fuel suction hose (2),

8.9.2

Connect tank vent hose (1) to
filter housing (arrow)
– push it fully onto the stub.

– Turn the pin (1) until the slot is in

line with the throttle cable.

Press down the throttle lever (2).

545RA289 TG

545RA041 TG

545RA042 TG

– Fit throttle cable (1) in the pin's

(2) slot.

Turn the pin until the nipple is
properly seated (arrow).

– Check operation

– squeeze throttle trigger on
handle as far as stop. The throttle
shutter must be fully open, adjust
throttle cable if necessary,

8.6.2

Fit the short circuit wire (1) in the
guide (arrow).

545RA043 TG

545RA044 TG

Содержание FS 40



















































































Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды

Stihl FS 40, Руководство по обслуживанию

Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды