Stihl FS 40 Скачать руководство пользователя страница 26

Страница: 26 / 82

Series 4144 Components FC, FS, KM

Installing

– Thread the short circuit and

ground wires through the hole
(arrow) in the handle molding.

Push the straight terminals of the
ground and short circuit wires
firmly onto the stop switch
connector tags.

Position the stop switch (1) so
that the lug (2) engages the slot
(arrow) in the opening.

545RA085 TG

545RA086 TG

Push the protective tube (1) and
throttle cable (2) into their seats
(arrows) in the handle molding.

Fit the wires, ground wire first, in
the guide (arrows) – position the
wires next to one another without
loops.

The throttle cable sleeve (1) must
locate in its seat in the handle
molding (2).

– Install the control levers,

7.4

– Install the throttle cable in the

control handle,

8.6.1

545RA088 TG

545RA089 TG

– Fit the handle molding (1) in

position.

Insert screws (arrows) and
tighten them down firmly.

Push the protective tube (1) with
wires and throttle cable into the
engine housing through the
opening (arrow).

Press the protective tube (1) into
its seat (arrow).

545RA090 TG

545RA091 TG

545RA076 TG

Содержание FS 40



















































































Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды

Stihl FS 40, Руководство по обслуживанию

Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды