Stihl FS 40 Скачать руководство пользователя страница 19

Страница: 19 / 82

Series 4144 Components FC, FS, KM

Push short circuit wire (1) and
ground wire (2) firmly onto the
connector tags.

The short circuit and ground wires
must be properly seated in the
guides (arrows).

The ignition lead (1) must be inside
the web (arrow) when the shroud is
fitted.

545RA045 TG

545RA062 TG

545RA047 TG

Place the shroud (1) in position
behind the air baffle (arrows).

– Push the shroud (1) down until it

engages the locking tabs.

Fit the screw (arrow).

– Turn the machine over.

Insert screws (arrows) and
tighten them down firmly.

545RA048 TG

545RA054 TG

545RA049 TG

Insert the screws (1)
– do not tighten them down yet.

– Reassemble all other parts in the

reverse sequence.

– Tightening torques,

3.4

Push on the protective cap (1) as
far as stop.

– Make sure the lug on the spark

plug boot (arrow) engages.

545RA290 TG

Содержание FS 40



















































































Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды

Stihl FS 40, Руководство по обслуживанию

Результаты поиска

Содержание FS 40

Отзывы:

Похожие инструкции для FS 40

Бренды по названию

Популярные бренды