Stevens AeroModel SQuiRT-700 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 21

Stevens AeroModel SQuiRT-700 Скачать руководство пользователя страница 14

19

Wing Assembly

1.

Build the sub assemblies for the wing.

See illustration below to reference part assemblies:

•

3/32” Balsa wing spar S1 from S1a, S1b, and S1c (one spar)

•

3/16” Balsa wing trailing edge TE1 from TE1a and TE1b (two each)

•

3/32” Balsa wing D-LOC™ sheeting TOP W2 from W2a and W2b (two each)

•

3/32” Balsa wing D-LOC™ sheeting BOTTOM W1 from W1a and W1b (two each)

2.

You’ll need to locate the 3/32” balsa ribs R2 (there are 5 of R2 in each side) Key the S1 spar assembly to one of
the 1/16” Balsa W1 lower D-LOC™ parts and lock the spar to W1 with each of the five R2 ribs. Reference this
photo and the plan sheet for placement. Lay this half of the wing on your flat building surface and glue the
spar, ribs, and W1 together. Repeat for the opposite wing half. Tip! the spar is notched to only fit on part W1 in
one direction if the part does not fit do not try and force the fit. Additionally, part W1 is etched indicating where
the inner R1 rib will meet W1.

3.

Next add the 3/32” ribs R3 at each tip of the wing as indicated in the photo below.

© 2005 Stevens AeroModel all rights reserved.

«
...
12
13
14
15
16
...
»

Содержание SQuiRT-700






















Отзывы:

Нет отзывов