© 2008 Stevens AeroModel.
Page 3 of 52
REQUIRED TO COMPLETE KIT:
Kit Contents
:
Laser Cut Wood (21 Sheets – See inventory on following pages)
Computer Drawn Plan Set
Illustrated Instruction Manual
Flat Stock and Push-Rods:
o
4 - 1/4 in. x 24 in. Square Balsa Leading Edge
o
1 - Pre-Bent Landing Gear (0.125 in.)
o
2 - 48 in. length Flat Carbon Fiber Stock
o
1 - DuBro Micro2 30in Pushrod System (DUB922)
o
1 - Pair 2-1/4 in. foam wheels
Large Hardware Bag: (4x6 Bag):
o
1 - Pair Delrin wing tip joiners
o
1 - Package Rubber Bands #33
o
1 - 4 in. length 1/16 in. aluminum tubing
o
1 - 4 in. length 1/32 in. music wire
o
3 - 3/16 in. x 3.75 in. Hardwood Dowels
Small Hardware (2x3 Bag):
o
1 - 1 in. length 3/32 in. ID silicone fuel tubing
o
2 - DuBro Micro2 Control Horns (1 pkg. / DUB919)
o
2 - DuBro Mini EZ Connectors (1 pkg. / DUB845)
o
2 - 1/8 in. star washers (wheel retainers)
o
2 - 4-40 x 3/8 in. Nylon Machine Screw
o
2 - 4-40 x 1-1/2 in. Nylon Machine Screw
o
4 - 15/32 in. x 1/8 in. OD Aluminum Tubing (anti rotation pins)
o
4 - 4-40 x 3/8 in. Machine Screw (motor mounting)
o
4 - #2 x 1/4 in. Screw (A20-20L motor mounting)
o
4 - assorted small black rubber bands
o
8 - 4-40 Blind Nut
o
10 - 3/16 in. Neo. Magnet
Recommended Finishing Items
:
1.
2 Rolls of AeroFILM or AeroFILM Lite (Solarfilm, Solarfilm Solite, or Nelson Lite Film may be substituted).
Suggested Electronics:
1.
2 – High performance micro servos (Hitec HS-55 or HS-65)
2.
1 – Hitec HS-56 sub micro servo (for spoiler installation)
3.
1 – 6 in. servo extension (for spoiler installation)
4.
1 – Full range micro receiver (Castle Creations/Berg Micro Stamp 4 or 4L)
Power Systems:
1.
Hacker A30-28S, E-Flite Park 480 1020kv, SA Sport 480 A2810-11
2.
9x5-10x5 APC-E Propeller. If you desire to utilize a folding propeller you will be required to reverse the motor
shaft of the Hacker and VSport motor - Out of the box the E-Flite motor is better prepared to accept a collet
style yoke and folding propeller assembly. We suggest using high quality Aeronaut Blades and an aluminum
yolk assembly. See
www.stevensaero.com
for suggested items for this model.
3.
11.1v 2100mAh LiPo (Rated for 15C discharge).
4.
Castle Creations Thunderbird 36 or Phoenix 25 ESC – (Enable propeller braking)
Building Supplies Required:
1.
Thin CA (super glue) and glue tips
2.
Medium CA (super glue) and glue tips
3.
Thread Locking Compound (Blue)
4.
Hobby knife and blade(s) #11 and straight edge
5.
Fine grit sand paper 250/400/600 and sanding block
6.
Clear tape ¾” wide scotch or DuBro hinge tape.
7.
Balsa wood filler
8.
.047 in., 1/16 in., 1/8 in., and 3/16 in. drill bits.