SteppIR CrankIR Скачать руководство пользователя | Manualshive

Страница: 42 / 52

background image

SteppIR Antennas



2112 116th Ave NE #1-5, Bellevue, WA 98004



Tel: 425.453.1910



www.steppir.com

Page 42

Once the tangle is fixed, simply reverse the procedure, making sure all of the
spacers are in place. THE BRUSH SPRINGS UP WHEN THE SHAFT IS REMOVED.
WHEN YOU RE-INSERT THE SHAFT YOU MUST PUSH THE BRUSH DOWN WITH
A SMALL SCREWDRIVER OR OTHER TOOL SO THE BRUSH WILL NOT BECOME
DAMAGED AS THE SHAFT IS INSERTED.

WIRE/CORD CAN’T BE MOVED WITH CRANK

Wire/Cord  has  gotten  wrapped  around  the  pulleys  at  the  Pole  Tip  Tensioner.
Lay  antenna  down  and  untangle  the  Wire/Cord.    Make  sure  you  threaded  it
through as shown in the manual.  The same applies to the Tunable Radial Unit
pulley(s).

Check for kinks in the wire that can’t get through the pulleys.

(16d)

«
...
40
41
42
43
44
...
»

Содержание CrankIR





















































Отзывы:

Нет отзывов

Похожие инструкции для CrankIR

Бренд: Tallymatics Страницы: 9

Бренд: Maco Antennas Страницы: 9

Бренд: M2 Antenna Systems Страницы: 3

Бренд: NZSAT Страницы: 12

Бренд: Intellian Страницы: 63

NextG 007GTi PRO

Бренд: Datacom Страницы: 35

Бренд: Philips Страницы: 24

Бренд: Oricom Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 7

Бренд: Pioneer Страницы: 4

Бренд: Omron Страницы: 135

Бренд: Crest Audio Страницы: 4

AntennaMast AM2

Бренд: Will Burt Страницы: 34

Бренд: TECHNI-CONTACT Страницы: 2

Бренд: Metronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды