manualshive.com logo in svg

SteppIR CrankIR, Руководство по сборке и инструкция

Поделиться
Скачать
SteppIR CrankIR Скачать руководство пользователя страница 18

SteppIR Antennas  

  2112 116th  Ave NE #1-5, Bellevue, WA 98004  

 

 Tel: 425.453.1910  

  www.steppir.com 

 

Page 18 

 3. Attach the Pole Tip Tensioner to the tip of the telescoping pole 

(3a)

 and 

tighten the four wingnuts on the saddle clamp 

(3b)

.  Deploy the two 

fiberglass arms with pulleys by loosening the two hand screws 

(3b)

 enough 

to allow pulling the white plastic blocks out enough to clear the channel in 
the gray plastic block. Now rotate the rods so they are extended out roughly 
perpendicular to the telescoping pole 

(3c)

.  Push both white plastic blocks 

down into the channel so they bottom out and tighten the hand screws 

(3d)

.  

 

 

     Next, extend the first two or three tip sections of the pole and pull them 

tight enough to lock them in place during use 

(3f)

. We recommend securing 

the pole joints with electrical tape to prevent inadvertent collapsing of the 
pole. Taping must be done if guy ropes are attached to the pole. 

Rotate the Pole and Tensioner Block so the back of the block now faces 

“forward” 

(3e). 

Turning the block around greatly reduces the possibility of 

the cord/wire catching on the wingnuts or hand screw heads. 

(3a) 

(3c) 

(3d) 

(3e) 

(3b) 

Hand Screws 

Hand screws 

Wingnuts 

Pole Tension Block 

Reverse Side 

Содержание CrankIR





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды