SteppIR CrankIR Скачать руководство пользователя | Manualshive

Страница: 11 / 52

background image

SteppIR Antennas



2112 116th Ave NE #1-5, Bellevue, WA 98004



Tel: 425.453.1910



www.steppir.com

Page 11

2. OPERATING CONTROLS

(continued)

GROUND LUG/TUNABLE RADIAL
UNIT MOUNTING HOLE

The .437 dia. (7/16”) hole for either the
included Ground Lug shaft with hand
locking knob or optional Radial Reel Unit
(PN 06401) mounts here. If the optional
Tunable Radial Unit is not used, fixed
length radials must be connected to the
Ground Lug Shaft.

RADIAL RELEASE KNOB

This knob has two functions, it locks the
Radial Reel shaft in any direction allowing
you to “point” the radial in the desired
direction and lock it. It also allows you to
remove the Radial Reel or the Ground Lug
by backing the knob out far enough to
disengage from the groove in the shaft
allowing the shaft to be pulled out. Make
sure the Radial Release Knob is tight during
operation to ensure radial electrical
connection.

WIRE REEL LOCK/DRAG

Locks the vertical radiator reel shaft, this
will keep the Wire/Cord from unwinding
during transport and storage. The amount

of drag is easily controlled by this knob as
well.

CORD REEL HOOK

Allows easy attachment / detachment of
the leader cord loop.

ANTENNA CONNECTOR

Connect 50-ohm coax terminated with a
PL-259 connector to this SO-239 connector
located on back of main unit. (See picture
below)

8

9

10

11

12

12

«
...
9
10
11
12
13
...
»

Содержание CrankIR





















































Отзывы:

Нет отзывов

Похожие инструкции для CrankIR

BAS-2333 LOGO-700

Бренд: BAS Страницы: 2

Pro Dual Band Soft Antenna

Бренд: dji Страницы: 30

Бренд: Crestron Страницы: 12

Бренд: Faria Страницы: 4

Бренд: Steren Страницы: 2

Бренд: Omron Страницы: 135

Бренд: Sea Tel Страницы: 93

Бренд: Sea Tel Страницы: 145

Бренд: Nice Страницы: 2

Бренд: Winegard Страницы: 10

ValuLine VHLP3 Series

Бренд: CommScope Страницы: 20

DAT 790 HD BOSS LR

Бренд: Televes Страницы: 4

Бренд: Televes Страницы: 4

Бренд: Steren Страницы: 2

Бренд: A.H. Systems Страницы: 20

TFX CAN link mobile 3311 Variant

Бренд: Eaton Страницы: 60

Бренд: KickAss Страницы: 12

Бренд: RadioWaves Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды