SteppIR CrankIR Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 52

SteppIR CrankIR Скачать руководство пользователя страница 6

SteppIR Antennas



2112 116th Ave NE #1-5, Bellevue, WA 98004



Tel: 425.453.1910



www.steppir.com

Page 6

The CrankIR is a lightweight, high
performance, extremely portable antenna
that is suitable for use both in the field or
at home when stealth operation is desired.
The entire antenna collapses down to less
than 24” and can be assembled and on the
air in less than ten minutes.

The basic CrankIR model covers from 40m
– 2m and has a power rating of 1500 watts.
The vertical radiator is supported by the
included 16’ fiberglass pole consisting of
ten sections, which when collapsed is 23”
long.  For 80m capability we offer the 80m
Option Kit (PN 06415) which includes
fiberglass extension tubes and a longer
wire on the optional Radial Unit (PN
06401), see previous page. The antenna
uses highly flexible 18 gauge copper wire
for the radiating elements resulting in
lightweight and high efficiency.  This
antenna is quickly and easily manually
tuned by adjusting the hand cranked wire
reels.

The element wire is marked with color-
coded band indicators (see pg. 13), to
select a band simply run the wire in or out
until the appropriate marker appears just
above the Wire Guide Block.

High efficiency is achieved by design; there
are no coils, only capacity hat type

resonating is used. There are no matching
networks; matching is accomplished by
very low loss off-center feeding.  When the
vertical radiator is shorter than 1/4
wavelength (WL) the impedance drops
significantly which then requires some way
to match the lower antenna impedance to
the 50 ohm transmitter.  On the CrankIR,
matching is done by off-center feeding the
antenna.  This is accomplished by
extending the radial much longer than the
normal 1/4 WL. By simply moving the
feedpoint away from the center, a higher
impedance is obtained with very little loss.
The farther you move from the center the
higher the impedance is.  This method
does result in increased imbalance so we
provide a specially designed balun to
insure the RF does not go down the
feedline.  Our patented loop element
design resonates the antenna without the
use of lossy coils.  This results in a higher
radiation resistance (by a factor of up to
2:1) than the same amount of coil loading;
this, in turn, increases antenna efficiency.

1. CRANKIR INTRODUCTION

«
...
4
5
6
7
8
...
»

Содержание CrankIR





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды