manualshive.com logo in svg

SteppIR CrankIR, Руководство по сборке и инструкция

Поделиться
Скачать
SteppIR CrankIR Скачать руководство пользователя страница 28

SteppIR Antennas  

  2112 116th  Ave NE #1-5, Bellevue, WA 98004  

 

 Tel: 425.453.1910  

  www.steppir.com 

 

Page 28 

12. Lock the Radial Wire Reel 

(12b) 

by turning the Wire Reel Lock Knob  

and then loosen the Cord Reel Drag/Lock Knob  

(12a). 

Now grab the 

pulley(s) and bungee and pull the cord out to the support(s) for the radials, 
the cord will reel off the Cord Reel  

(12b)

 . The Wire Reel remains 

stationary, thus keeping the wire off the ground where it might coil up and 
kink. After the radials have been attached to the supports using the bungee 
cord(s), adjust the tension of the Wire/Cord by turning the Cord Reel Crank 
Handle   

until the Wire/Cord is suspended off the ground. Tighten the 

Cord Reel Drag/Lock 

and turn the crank such that the radial wire is fed 

out to the desired length. Loosen the Cord Reel Drag knob and adjust the 
tension until the Wire/Cord is well off the ground but not so tight that it puts 
undue force on the tripod and pulls it over. If you plan to use the antenna on 
only a couple bands, the tension on the bungee is not critical. If you want to 
cover 40m-6m, crank the radial out to the 20m point (about 16’) and adjust 
for the minimum acceptable tension; you can now go from 40m to 6m 
without adjusting the tension. 

18 

15 

19 

16 

15 

17 

Bear in mind you must be able to freely access the Radial Unit Crank Handle 
so be sure to align the Radial Unit accordingly.  If your chosen alignment 
does not allow turning the Radial Unit Crank Handle , simply turn the tripod 
to allow access to the Radial Unit Crank Handle while keeping the radial 
pointed in the desired direction. 

Содержание CrankIR





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды