manualshive.com logo in svg

SteppIR CrankIR, Руководство по сборке и инструкция

Поделиться
Скачать
SteppIR CrankIR Скачать руководство пользователя страница 3

SteppIR Antennas  

  2112 116th  Ave NE #1-5, Bellevue, WA 98004  

 

 Tel: 425.453.1910  

  www.steppir.com 

 

Page 3 

THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES 
CAN RESULT IN DEATH, OR SERIOUS INJURY. DO NOT INSTALL THIS ANTENNA 
WHERE THERE IS ANY POSSIBILITY OF CONTACT WITH HIGH VOLTAGE OR ARC-
OVER FROM POWER CABLES OR SERVICE DROPS TO BUILDINGS. THE ANTENNA 
SUPPORT MAST OR RADIAL(S) MUST NOT BE CLOSE TO ANY POWER LINES 
DURING INSTALLATION, REMOVAL, OR IN THE EVENT PART OF THE SYSTEM 
SHOULD ACCIDENTALLY FALL. EVEN BEING CLOSE TO POWER CABLES HIGH 
VOLTAGE AURALS CAN CAUSE LETHAL VOLTAGES IN THE ANTENNA. 

FOLLOW THE GUIDELINES FOR ANTENNA INSTALLATIONS RECOMMENDED BY THE 
U.S. CONSUMER PRODUCT SAFETY COMMISSION. 

EXTREME CARE MUST BE USED FOR YOUR SAFETY. YOU MUST INSURE THAT 
WHILE THE CRANKIR IS IN OPERATION NEITHER PEOPLE NOR PETS CAN COME IN 
CONTACT WITH ANY PORTION OF THE ANTENNA INCLUDING THE RADIALS. 

DEADLY VOLTAGES AND CURRENTS MAY EXIST. ALSO, SINCE THE EFFECTS OF 
EXPOSURE TO RF ARE NOT FULLY UNDERSTOOD, LONG TERM EXPOSURE TO 
INTENSE RF FIELDS IS NOT RECOMMENDED.  

RADIALS, BOTH ELEVATED AND GROUND MOUNTED SHOULD BE MARKED WITH 
WARNING TAPE AT APPROPRIATE INTERVALS TO VISUALLY ALERT PEOPLE TO THEIR 
PRESENCE. 

ALL DEPLOYMENTS OF THE CRANKIR SHOULD BE GUYED TO AVOID THE RISK OF 
SERIOUS INJURY FROM THE ANTENNA FALLING. 

WARNINGS 

Содержание CrankIR





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды