STEMME S6 Скачать руководство пользователя

Страница: 174 / 215

FLIGHT MANUAL TSA-M, VARIANT S6

Doc.-No.: P400-006.000 E

Page: 7-19

Revision: ---

Date of Issue: 07. October 2008

Date of Rev.: --.--.----

7.10.2 Entry

The method of entry varies individually and depends on the size and agility of

the pilot.

The following procedure is a convenient and comfortable method of entering the

aircraft:

•

Stand with your back facing the cockpit.

•

Place one hand on the leading-edge of the wing near the wing-root. Place

the other hand on the cockpit frame.

•

Raise yourself off the ground with both arms and jumping slightly upwards.

Move to sit on the cockpit-frame at the lowest spot.

•

Recover your balance and support yourself on the center console in the

cockpit. Then move legs-first into the cockpit.

7.10.3 Cabin-Ventilation

The ventilation of the cabin occurs individually for each seat and the canopy.

The air for the cabin-ventilation flows from the free-airflow beneath propeller-

spinner into two air-inlets. From there it is lead into a centralized air-distribution-

system, where the airflow splits to the separate vents.
The canopy-vents are located near the canopy-hinge. They are operated with a

Bowden-cable installed at the center top of the instrument-panel.
Each seat for the pilot and copilot has one vent in the leg-room and two vents in

the seating-area which supply the flight crew with fresh air. Ventilation can be

controlled individually for each seat at the vents near the knees.
Operation of all vent-controls follows the same principal:
If the vent-control is fully PULLED rearward, the corresponding vent is fully

OPEN. Otherwise, if the vent-control is fully PUSHED forward, the

corresponding vents are fully CLOSED.
Additional ventilation can be obtained by opening the side-windows of the

canopy.

Содержание S6
























































































































































































































Результаты поиска

Содержание S6

Отзывы:

Похожие инструкции для S6

Бренды по названию

Популярные бренды

STEMME S6, Руководство по эксплуатации самолета

Результаты поиска

Содержание S6

Отзывы:

Похожие инструкции для S6

Бренды по названию

Популярные бренды