manualshive.com logo in svg

Stellar Hearth Products 3BY-24GL, Инструкция по установке и эксплуатации

Поделиться
Скачать
Stellar Hearth Products 3BY-24GL Скачать руководство пользователя страница 43

Page 43

16400-7802 GBY REV G

D - COMBUSTIBLE OR NON-COMBUSTIBLE    

      BACKER MATERIAL (I.E. SHEETROCK)

E - COMBUSTIBLE 

MANTEL

F - COMBUSTIBLE 

HEARTH

G. ACCESS PANEL

i. COMBUSTIBLE FRAMING 

AND FINISHING MATERIAL

A. No combustible materials may be within 6” [152mm] of the top of the fireplace.
B. 1/2” [12.7]  CLEARANCE TO COMBUSTIBLES ON SURFACE. The fireplace ships with standoffs in place to ensure a 1/2” clearance to     
combustibles is maintained on the surface. See Figure 10A.1. If the standoffs are removed, only non-combustible material can be installed against  
the surface of the fireplace such as a non-combustible backer cement board. 1/2” [12.7mm] minimum thickness must be used in the space* between the 
top of the 3’’ trim to the combustible framing the full width of the fireplace. The space* includes a 7” [178mm] minimum above the top of the fireplace that 
is recommended for ease of attachment. *= 15" [381] for 3'-7' units and 19" [483] for 8' units.
See Figure 10A.2
C. Combustible material may cover the non-combustible area mentioned in B. 
D. Combustible finishing materials allowed.
E. Combustible mantel may be placed above the top of the glass viewing area. There are no restrictions on mantel depth.
F. Combustible hearth may be placed below the bottom of the glass viewing area. 
G. Flat covers will cover the components access.  Gas and electric inlets are located behind this panel. There are four access panel options all  
     located on the pilot side of the fireplace; front (shown above), side, back and inside behind the glass. 
     Please take consideration of which option will be used to access the components for service later during planning. 
I. Combustible framing and finishing materials allowed.

C - COMBUSTIBLE OR NON-COMBUSTIBLE    

      FINISHING MATERIAL

A

 STANDOFF

REFER TO (B)

B

3” TOP TRIM

COMBUSTIBLE FRAMING

11 - FINISHING

A.1 FINISHING THE WALL - USING THE PROVIDED 1/2" STANDOFFS

NOTE: 

DO NOT 

BAYCE ANY OF THE BLACK PAINTED SURFACES WITH SCREWS, RIVETS, ETC. 

 

THIS INCLUDES THE 3" BLACK TOP AND BOTTOM GLASS TRIM AND ANY PAINTED SIDES ADJACENT TO THE GLASS. 

NOTE: REFER TO DIMENSIONS SECTION FOR ALLOWABLE FINISHING DIMENSIONS REQUIRED TO FIT THE GLASS 

 

PANELS INTO THE FIREPLACE. FINISHING MATERIALS MUST NOT OVERLAP THE DIMENSIONS HIGHLIGHTED IN GREEN ON 

PAGE 5. NEVER COVER THE GLASS WITH FINISHING MATERIALS.

NOTE: REFER TO SECTION 5 MANTEL REQUIREMENTS: NON-COMBUSTIBLE ZONE USING PROVIDED 1/2" STANDOFFS FOR 

MORE INFORMATION.

Figure 11A.1

Содержание 3BY-24GL





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды