Stellar Hearth Products 3BY-24GL Скачать руководство пользователя страница 4

1 - SAFETY INFORMATION

• 

Installation and repair should be done only by a qualified 

service person. The appliance should be inspected by a 

qualified service person before use. Annual inspection by a 

qualified service person is required to maintain warranty. More 

frequent cleaning may be required due to excessive lint from 

carpeting, bedding materials, etc. It is imperative that control 

compartments, burners and circulation air passageways of the 

appliance be kept clean.

• 

Children and adults should be alerted to the hazards of high 

surface temperatures and should stay away to avoid burns or 

clothing ignition.

• 

Young children should be carefully supervised when they are 

in the same room as the appliance. Toddlers, young children 

and others may be susceptible to accidental contact burns. A 

physical barrier is recommended if there are at risk individuals 

in the house. To restrict access to a fireplace or stove, install 

an adjustable safety gate to keep toddlers, young children and 

other at risk individuals out of the room and away from hot 

surfaces.

• 

Clothing or other flammable material should not be place on or 

near the appliance.

• 

Adequate accessibility clearances for servicing and proper 

operation must be maintained.

• 

This appliance must not share or be connected to a chimney 

flue serving any other appliance.

• 

Keep area around the appliance clear of combustible materials, 

gasoline and other flammable vapor and liquids.

• 

The flow of combustion and ventilation air must not be 

obstructed. 

DO NOT

RISK OF FIRE

IMPORTANT NOTE

STOP!

HOT GLASS WARNING

A. SAFETY ICON DESIGNATIONS

B. IMPORTANT SAFETY CONSIDERATIONS

• 

Due to high temperatures the appliance should be located out 

of traffic and away from furniture and draperies.

• 

The glass front or any part removed for servicing the appliance 

must be replaced prior to operating the appliance. Work should 

be done by a qualified service technician. 

• 

Clean glass only when cool and only with non-abrasive 

cleansers.

• 

Do not operate this appliance with the glass/frame assembly 

removed, cracked or broken. Replacement of the glass 

assembly must only be performed by a licensed or qualified 

service person. DO NOT SUBSTITUTE MATERIALS. 

• 

Do not strike or slam glass assembly. 

• 

Keep burner and control compartment clean.

• 

Do not use this fireplace if any part has been under water. 

Immediately call a qualified service technician to inspect this 

appliance and to replace any part of the control system and any 

gas control which has been under water.

• 

DANGER: 

Under no circumstances should any solid fuel 

(wood, coal, paper or cardboard etc.) be used in this appliance.

• 

STATE OF CA WARNING: 

This product and the fuels used 

to operate this product (liquid propane or natural gas), and 

the combustion of such fuels, can expose you to chemicals 

including benzene, which is known to the State of California to 

cause cancer and reproductive harm.  

 

         For more information go to: www.P65Warnings.ca.gov. 

Various safety icons appear throughout this installation manual. Please familiarize yourself with the icons making sure you understand the serious 
consequences that may occur if ignored or of handling the products inappropriately. 

This indicates additional instructions that you should consider 

during the installation.

This indicates something that you must never do.

This designates a danger of risk of fire or damage to property.

This indicates danger of serious bodily injury or property     

damage if glass is handled while still hot.

CAUTION

This indicates danger of serious bodily injury or property     

damage

This indicates notes that may include reviewing warnings on 

other pages throughout the manual 

This fireplace complies with ANSI Z21.50-2019/CSA 2.22-2019 Vented Gas Fireplaces and CAN/CSA P.4.1-15.

  Installation must conform with local building codes or in the absence of local building codes, 

with the National Fuel Gas Code, ANSIZ223.1/NFPA 54 - Current Edition, or the Natural or Propane Installation Code, CSAB149.1

Page 4

Содержание 3BY-24GL





















































Отзывы: