10
11
•
Press the spindle adjuster (e1) again and pull the spindle screw tight with a
wrench.
•
Be aware that the mould cutter depth must be re-adjusted.
ROTATION SPEED ADJUSTMENT
Comment:
Turn the machine off before changing the rotation speed.
Check the positioning and rotation of the mould cutter before operating the
machine!
Select the rotation speed with the switch for the rotation speed regulator (11).
•
You can select 7 different switch positions: From switch position „ 1“(11000 RPM)
to switch position „ 7 “ (30000RPM).The rotation speed can be set according to
the desired speed from a level of 1 through 5. The required rotation speed
depends on the working material and the type of work. The rotation speed can
best be determined by a test run.
•
After working with low rotation speed for a long time, allow the machine to cool
down for about 2 minutes with it running idle at maximum rotation speed.
(10) in the desired direction.
•
The desired drilling depth can simply be subtracted from the displayed centimeter
number. (Example : 4 cm is displayed on the scale, and you want to drill 2 mm.
So the scale should be adjusted to display 3.8 cm.) Lift the depth measuring stick
up, so that the read-off point on the scale (a1) shows the corresponding value.
(3.8 cm in the example)
•
Now adjust the depth measuring stick (9) with the new calibration. The depth
measuring stick can be locked in position by tightening the set screw (8). You now
have set the desired drilling depth.
•
Now loosen the height adjuster (12) to get the mould cutter ready for operation.
OPERATION
PROTECTIVE CLOTHING
•
If possible, wear designated gloves for protection from splinters and shavings.
•
While working, wear designated protective goggles. Flying shavings can cause
injury.
•
Wear hearing protection for protection against continuous noise in the work place.
•
Wear a designated dust mask for protection against airborne dust.
DRILLING DIRECTION
The drilling must always turn in the opposite running direction of the drill
(counter-rotation). The rotation direction is indicated by the arrow (3) on the front of
the machine.
5. SETTING UP THE ROUTER
ADJUSTMENT OF CUTTING DEPTH
•
Lower down supporting knee until the tool will touch the surface of the machined
piece, fix it by lever (12), and read the position on vertical ruler as initial (zero)
position.
•
Adjust the first depth level by guide (9), pointing to the highest level of the three-
position support (7), reading the size on vertical ruler and fix the supporting knee
with lever (12).
•
Fix depth guide (2) by the wing screw. (Adjust in advance the three levels of the
positioning support to the desired levels.)
•
The second and the third level of cutting depth can be achieved by only rotating
the disk of the three-position support (7) and moving the support knee until depth
guide (9) will touch the corresponding level of the support. Check the sizes on the
vertical ruler or by a reference part (test part).
CALIBRATION CALCULATION
You know the exact cutting depth in centimeters and would like to change it.
You would like to drill exactly a 2 mm deep screw into a wooden board, for example.
•
Insert the appropriate mould cutter.
•
Adjust the depth stopper (7), so that the height measuring stick shows the lowest
level when brought down.
•
Loosen the set screw (8) of the depth measuring stick.
•
Loosen the height adjuster (12) and press the drilling tool with the handle (2) far
under, so that it touches the work piece.
•
Secure this adjustment by tightening the height adjuster.
•
Make sure that the depth measuring stick (9) with the metal point (b1) is sitting on
the depth stopper.
•
Now the starting position can be read from the read-off point on the depth
measuring scale (a1).
•
The depth measuring stick (9) can be adjusted, so that the desired centimeter
number is displayed on the scale. Turn the adjuster of the depth measuring stick
See illustration (H).
Danger of accident! While drilling in normal rotational direction,
the router could be torn away from your hand.
•
Pay attention to the rotation direction of the driller head!
•
Only drill in counter-rotation!
TURNING ON/OFF
•
To operate the machine, press and hold the safety latch (16). Then press and hold
the big on/off switch (17). The drill is now turned on.
•
As soon as you let go of the on/off switch (17), the drill will turn off . In the case that
you let go of the safety latch (16), the on/off switch (17) will be locked again.
MOULD CUTTING
•
Loosen the height adjuster (12) and set the mould cutter on the work piece.
•
While operating, press the mould cutter until the height stopper (7) stops.
•
Continue pressing the mould cutter and tighten the height adjuster (12) again.
Now push the mould cutter as desired by grasping both router handles.
•
To turn the machine off, simply let go of both orange buttons (16,17) on the right
handle.
•
Hold the router firmly until the motor has stopped.
FREEHAND MOULD CUTTING
With freehand mould cutting, you can cut creatively, like drawing something by
hand. The router can be used without a guiding rod for this purpose. With freehand
mould cutting, it is safest when the router is laid flat.
