background image

9

HARD WATER

Where hard water conditions exist, water softening or the threshold 

type of water treatment is recommended.  This will protect the 

dishwashers, coffee urns, water heaters, water piping and other 

equipment.

See  MAINTENANCE  section  for  details  of  tank  cleanout 

procedure.

AIR REQUIREMENTS

REFER TO THE CURRENT EDITION OF THE “NATIONAL FUEL 

GAS CODE” ANSI Z223.1/NFPA 54.

 

WARNING

KEEP APPLIANCE AREA CLEAR AND FREE OF COMBUSTIBLE 

MATERIALS, GASOLINE AND OTHER FLAMMABLES, VAPORS 

AND LIQUIDS.

DO  NOT  OBSTRUCT  THE  FLOW  OF  COMBUSTION  OR 

VENTILATING AIR.

 

WARNING

FOR  SAFE  OPERATION  PROVIDE ADEQUATE AIR  FOR 

COMBUSTION AND VENTILATION.  AN INSUFFICIENT SUPPLY 

OF AIR  WILL  CAUSE  RECIRCULATION  OF  COMBUSTION 

PRODUCTS  RESULTING  IN AIR  CONTAMINATION  THAT 

MAY BE HAZARDOUS TO LIFE.  SUCH A CONDITION OFTEN 

WILL  RESULT  IN A YELLOW,  LUMINOUS  BURNER  FLAME, 

CAUSING CARBONING OR SOOTING OF THE COMBUSTION 

CHAMBER,  BURNERS AND  FLUE TUBES AND  CREATES A 

RISK OF ASPHYXIATION.

Where  an  exhaust  fan  is  supplied  in  the  same  room  with 

a  heater,  sufficient  openings  for  air  must  be  provided  in 

the  walls.   

UNDERSIZED OPENINGS WILL CAUSE AIR TO 

BE  DRAWN  INTO  THE  ROOM  THROUGH  THE  CHIMNEY, 

CAUSING POOR COMBUSTION. SOOTING MAY RESULT IN 

SERIOUS DAMAGE TO THE HEATER AND RISK OF FIRE OR 

EXPLOSION.

UNCONFINED SPACE

In buildings of conventional frame, brick, or stone construction, 

unconfined  spaces  may  provide  adequate  air  for  combustion, 

ventilation and draft hood dilution.

If the unconfined space is within a building of tight construction 

(buildings  using  the  following  construction:  weather  stripping, 

heavy insulation, caulking, vapor barrier, etc.), air for combustion, 

ventilation and draft hood dilution must be obtained from outdoors.  

The  installation  instructions  for  confined  spaces  in  tightly 

constructed buildings must be followed to ensure adequate air 

supply.

CONFINED SPACE

When  drawing  combustion  and  dilution  air  from  inside  a 

conventionally constructed building to a confined space, such a 

space shall be provided with two permanent openings, ONE IN OR 

WITHIN 12 INCHES (30.5cm) OF THE ENCLOSURE TOP AND 

ONE IN OR WITHIN 12 INCHES (30.5cm) OF THE ENCLOSURE 

BOTTOM.  Each opening shall have a free area of at least one 

square inch per 1000 Btuh (2,225mm

2

/kW) of the total input of all 

appliances in the enclosure, but not less than 100 square inches 

(645 square cm).

If  the  confined  space  is  within  a  building  of  tight  construction, 

air for combustion, ventilation, and draft hood dilution must be 

obtained from outdoors.  When directly communicating with the 

outdoors  or  communicating  with  the  outdoors  through  vertical 

ducts, two permanent openings, located in the above manner, 

shall be provided.  Each opening shall have a free area of not 

less than one square inch per 4000 Btuh (8,900mm

2

/kW) of the 

total input of all appliances in the enclosure.  If horizontal ducts 

are used, each opening shall have a free area of not less than 

one square inch per 2000 Btuh (4,450mm

2

/kW) of the total input 

of all appliances in the enclosure. 

VENT REDUCER

The SBD 250, 251, and 275 models are shipped with an 8” to 

6” diameter flue outlet adapter. Each adapter fits on top of the 

installed flue damper.  Use only vent reducers supplied with the 

unit.  The venting must comply with the NATIONAL FUEL GAS 

CODE, ANSI Z223.1/NFPA 54.

FIGURE 7

 ILLUSTRATION OF MINIMUM COMBUSTIBLE CLEARANCES IN AN ALCOVE

FIGURE 6

Содержание SBD100199*





































Отзывы: