Star SP712 Series Скачать руководство пользователя страница 25

Страница: 25 / 40

– 21 –

CAUTION

Wireless Communication

Do not use the device where using wireless devices is prohibited or may cause interference or danger.

The radio waves generated by the device may interfere with the operation of electronic medical devices. If

you are using any electrical medical device, contact its manufacturer for the restrictions on the use of the

device.

Security functionality for Bluetooth is installed in this product. Configure the security settings according to

the manual (available on the Star Micronics website) to reduce the risk of security issues.

This device supports Bluetooth.

Since this functionality may be limited by local regulations, first review the radio laws specific to the country

in which the product will be used.

Below is a list of laws this device has been approved by. As Star Micronics is committed to constant innova-

tion, revisions may be made without an announcement. Access the Star Micronics website for the latest listing

of approvals.

Please refer to Star Micronics website for the latest information and manuals.

Содержание SP712 Series









































Результаты поиска

Содержание SP712 Series

Отзывы:

Похожие инструкции для SP712 Series

Бренды по названию

Популярные бренды

Star SP712 Series, Руководство по оборудованию

Результаты поиска

Содержание SP712 Series

Отзывы:

Похожие инструкции для SP712 Series

Бренды по названию

Популярные бренды