Star SP712 Series Скачать руководство пользователя страница 13

Страница: 13 / 40

– 9 –

3-4. Connecting the Power Cord

Note:

Before connecting/disconnecting the power cord, make sure that power to the printer and all the devices

connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC
outlet.

(1) Check the label on the back or bottom of the printer to make sure its voltage matches that of the AC outlet. Also

make sure the plug on the power cord matches the AC outlet.

(2) If the power cord is not attached to the printer, plug the appropriate end into the AC inlet on the back of the

printer.

(3) Plug the power cord into a properly grounded AC outlet.

Important!

If the voltage shown on the label on the of your printer does not match the voltage for your area, contact your
dealer immediately.
The power cord is designed for use with this printer only. Do not connect it to any other device.

Содержание SP712 Series









































Результаты поиска

Содержание SP712 Series

Отзывы:

Похожие инструкции для SP712 Series

Бренды по названию

Популярные бренды

Star SP712 Series, Руководство по оборудованию

Результаты поиска

Содержание SP712 Series

Отзывы:

Похожие инструкции для SP712 Series

Бренды по названию

Популярные бренды