Star SP712 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

– 6 –

3-2-2. RS-232 Interface Cable

(1) Make sure the printer is turn off.

CAUTION

Before connecting/disconnecting the interface cable, make sure that power to the printer and all the devices

connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet.

(2) Connect the interface cable to the connector on the rear panel of the printer.

(3) Tighten the connector screws.

3-2-3. USB Interface Cable

Affix the ferrite core onto the USB cable as shown in the illustration below and make sure to pass the cable through the

cable support as shown in the illustration.

«
...
8
9
10
11
12
...
»

Содержание SP712 Series









































Отзывы:

Нет отзывов

Похожие инструкции для SP712 Series

Бренд: Kees van der Westen Страницы: 26

Бренд: Kees van der Westen Страницы: 54

Mirage Slim Jim

Бренд: Kees van der Westen Страницы: 32

Бренд: Nespresso Страницы: 36

CafeRomatica 960

Бренд: Nivona Страницы: 30

Бренд: Wolfgang Puck Страницы: 18

Бренд: Saeco Страницы: 99

Бренд: STARBUCKS Страницы: 23

Бренд: DèLonghi Страницы: 18

Бренд: Kalorik Страницы: 20

Бренд: Xo Страницы: 32

Бренд: Orbegozo Страницы: 25

42820 Design Bread Maker Plus

Бренд: Gastroback Страницы: 32

the Barist Express SES875

Бренд: Sage Страницы: 48

Бренд: Curtis Страницы: 43

U-3018CLRINT-40C

Бренд: U-Line Страницы: 50

Бренд: Alpina Страницы: 39

Бренд: U-Line Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды