Star Comm V.32bis страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 37

background image

9

Z0

Soft reset and restore stored in profile 0.

Z1

Soft reset and restore stored profile 1.

AT& COMMANDS

&Cn - RLSD (DCD) Option

This command controls the RLSD output in accordance with the parameter supplied.

&CO RLSD remains ON at all times.
&C1 RLSD follows the state of the carrier. (Default)

&Dn - DTR Option

This command interprets the ON to OFF transition of the DTR signal from the DTE in accordance with the
parameter supplied.

&DO DTR is ignored and assumed on.

&D1  DTR drop forces modem to command state without disconnecting.
&D2  DTR drop forces hang up, auto-dial is inhibited. (Default)
&D3  DTR drop forces modem to soft reset.

&Fn - Restore Factory Configuration (profile)

This command loads the factory default configuration (profile).

&F0 Restore factory configuration 0.
&F1 Restore factory configuration 1.

&Gn - Select Guard Tone

This command controls the generation of guard tone.

&G0  Disables guard tone.
&G1  Disables guard tone.
&G2  Selects 1800 Hz guard tone.

&Jn - Telephone Jack Control

This command is only included for compatibility and performs no function except to load the S-Register.

&J0

&J0 command. (Default)

&J1

&J1 command.

&Kn - Flow Control

This command defines the DTE/DCE (terminal/modem) flow control mechanism.

&K0  Disables flow control.
&K3  Enables RTS/CTS flow control. (Default)
&K4  Enables XON/XOFF flow control.
&K5  Enables transparent XON/XOFF flow control.
&K6  Enables both RTS/CTS and XON/XOFF flow control.

«
...
8
9
10
11
12
...
»

Содержание V.32bis






































Отзывы:

Нет отзывов

Похожие инструкции для V.32bis

Бренд: iRZ Страницы: 20

Бренд: P1 Страницы: 5

Бренд: P1 Страницы: 17

Бренд: P1 Страницы: 2

Бренд: 9XTend-NEMA Страницы: 66

Бренд: Eaton Страницы: 83

Бренд: ZyXEL Communications Страницы: 70

Бренд: Draytek Страницы: 288

Бренд: TURBOCOMM Страницы: 6

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 4

Бренд: ADTRAN Страницы: 88

MobilityPass 3G

Бренд: Nokia Страницы: 6

Internet Stick CS-19

Бренд: Nokia Страницы: 17

Бренд: Nokia Страницы: 17

Бренд: Nokia Страницы: 18

Бренд: Nokia Страницы: 17

Internet Stick CS-18

Бренд: Nokia Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды