Star Comm V.32bis Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 37

background image

10

&Ln - Leased Line Operation

This command selects dial up or leased line operation.

&L0

Selects dial up operation.

&L1

Selects leased line operation.

&Mn - Asynchronous/Synchronous Mode Selection

This command determines the DTR operating mode. The modem treats the &M command as a subset of
the &Q command.

&M0  Selects direct asynchronous operation.
&M1  Selects synchronous connect mode with asynch off-line command mode.
&M2  Selects synchronous connect mode with asynch  off-line command mode. Same as &M1

except that &M2 enables DTR dialing of directory slot 0. The modem will disconnect if DTR is
OFF for more than the period in S25.

&M3 Selects synchronous connect mode. This mode allows DTR to act as a talk/data switch. The

call is manually initiated while DTR is inactive. When DTR becomes active, the handshake
proceeds in originate or answer mode according to S14 bit 7.

&Pn - Select Pulse Dial Make/Break Ratio

This command determines the make/break ratio used during pulse dialing.

&P0 Selects 39%-61% make/break ratio at 10 pulses per second. (Default)

&P1  Selects 33%-67% make/break ratio at 10 pulses per second.
&P2  Selects 39%-61% make/break ratio at 20 pulses per second.
&P3  Selects 33%-67% make/break ratio at 20 pulses per second.

&QN - Sync/Async Mode

This command is an extension of the &M command is used to control the connection modes permitted. It is
used in conjunction with S36 and S48.

&Q0  Selects direct asynchronous operation.
&Q1  Selects synchronous connect mode with asynch off-line command mode.
&Q2  Selects synchronous connect mode with asynch off-line command mode and enables DTR

dialing of directory 0.

&Q3 Selects synchronous connect mode with asynch off-line command mode and enables DTR to

act as Talk/Data switch.

&Q4 Selects AutoSync operation. Auto-synch operation when used in conjunction with the Hayes

Synchronous Interface (HSI) capability in the DTE, provides synchronous communication
capability from an asynchronous terminal.

&Q5 The modem will try to negotiate an error-corrected link. (Default)
&Q6 Selects asynchronous operation in normal mode (speed buffering).

&Rn - RTS/CTS Option

This selects how the modem controls CTS. CTS operation is modified if the hardware flow control is
selected.

&R0 In sync mode, CTS tracks the state of RTS; the RTS to CTS delay is defined by S26. In async

«
...
9
10
11
12
13
...
»

Содержание V.32bis






































Отзывы:

Нет отзывов

Похожие инструкции для V.32bis

I-STORM USB A01-AU1

Бренд: Atlantis Land Страницы: 2

Бренд: Sel Страницы: 16

Бренд: Funk-Electronic Piciorgros Страницы: 284

Photo Backup Stick Universal

Бренд: Paraben Страницы: 10

Бренд: Hayes Microcomputer Products Страницы: 39

Бренд: Data-Linc Group Страницы: 31

Бренд: D-Link Страницы: 42

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 42

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 66

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 84

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 154

Бренд: D-Link Страницы: 57

Бренд: D-Link Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды