Star Comm V.32bis Скачать руководство пользователя страница 9

Страница: 9 / 37

Sn - Read/Write S-Register

The modem selects an S-Register, performs an S -Register read or write function, or reports the value of an
S-Register.

Establishes S-Register n as the last register accessed.

n=v

Sets S-Register n to the value v.

Reports the value of S-Register n.

T - Set Tone Dial Default

This command forces DTMF dialing until the next P dial modifier or P command is received.

Vn - Result Code Form

This command selects the sending of short-form or long-form result codes to the DTE.

Enables short-form (terse) result codes.

Enables long-form (verbose) result codes. (Default)

Wn - Connect Message Control

This command controls the format of CONNECT messages.

Modem reports DTE speed. (Default)

Modem reports line speed error correction protocol and DTE speed.

Modem reports the DCE speed.

Xn - Extended Result Codes

This command selects which subset of the result messages will be used by the modem to inform the DTE of
the results of commands.

Disables monitoring of busy tones, sends only OK, CONNECT, RING, NO CARRIER, ERROR,
and NO ANSWER result codes. Blind dialing is enabled.

Disables monitoring of busy tones, sends only OK, CONNECT, RING, NO CARRIER, ERROR,
NO ANSWER, and CONNECT XXXX(XXXX=rate). Blind dialing is enabled.

Disables monitoring of busy tones, sends only OK, CONNECT, RING, NO CARRIER, ERROR,
NO DIAL TONE, NO ANSWER, and CONNECT XXXX.

Enables monitoring of busy tones; send only OK, CONNECT, RING, NO CARRIER, ERROR,
NO ANSWER, and CONNECT XXXX. Blind dialing is enabled.

Enables monitoring of busy tones, sends all messages. (Default).

Yn - Long Space Disconnect

This command enables/disables the generation and response to long space disconnect.

Disables long space disconnect. (Default)

Enables long space disconnect.

Zn - Soft Reset and Restore Profile

The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter
supplied. If no parameter is specified, zero is assumed.

Содержание V.32bis






































Результаты поиска

Содержание V.32bis

Отзывы:

Похожие инструкции для V.32bis

Бренды по названию

Популярные бренды

Star Comm V.32bis, Руководство пользователя

Результаты поиска

Содержание V.32bis

Отзывы:

Похожие инструкции для V.32bis

Бренды по названию

Популярные бренды