Star Comm V.32bis страница 8 Скачать руководство пользователя

Страница: 8 / 37

In - Identification

The modem reports to the DTE the requested result according to the command parameter.

Reports product code.

Reports a pre-computed checksum.

Reports "OK".

Reports firmware revision (VX.XXX) model code.

Reports OEM defined identifier string in Hayes compatible binary format.

Reports Country Code parameter.

Reports modem data pump model and internal code revision.

Reports the DAA code resulting from MCU interrogation of the DAA for auto DAA recognition.

Ln - Speaker Volume

The modem sets the speaker volume control according to the parameter supplied.

Low volume.

Low volume. (Default)

Medium volume.

High volume.

Mn - Speaker Control

Speaker is always off.

Speaker is on during call establishment, but off when receiving carrier. (Default)

Speaker is always on.

Speaker is off when receiving carrier and during dialing, but on during answering.

Nn - Automode Enable

This command enables or disables Automode detection.

Automode detection is disabled.

Automode detection is enabled. (Default).

On - Return to On-Line Data Mode

This command determines how the modem will enter the on-line data mode.

Enters on-line data mode, without a retrain.

Enters on-line data mode with a retrain.

P - Set Pulse Dial Default

This command forces pulse dialing until the next T dial modifier or T command is received.

Qn - Quiet Results Codes Control

The command enables or disables the sending of result codes to the DTE according to the parameter
supplied.

Enables result codes to the DTE. (Default)

Disables result codes to the DTE.

Содержание V.32bis






































Результаты поиска

Содержание V.32bis

Отзывы:

Похожие инструкции для V.32bis

Бренды по названию

Популярные бренды

Star Comm V.32bis, Руководство пользователя

Результаты поиска

Содержание V.32bis

Отзывы:

Похожие инструкции для V.32bis

Бренды по названию

Популярные бренды