ST ST7 Series Скачать руководство пользователя страница 117

Страница: 117 / 317

117/317

5 - Peripherals

Set the TAOC2HR-TAOC2LR register pair to the number of ticks corresponding to the

duration of the whole cycle (this number depends on the clock frequency), minus 4.

Set the OLVL2 bit in the TACR1 register to the state required for the output pin for the

duration of the pulse, and OLVL1 in TACR1 to the complement of this state to terminate the

pulse.

Set the PWM bit in TACR2 to enable the Pulse-Width Modulation mode.

Set the PWM bit in TACR2 to enable the output pin.

The OCF1 and OCF2 bits are never set in this mode. However, the leading edge of the pulse,

corresponding to the start of cycle, can generate an interrupt if desired. Actually, the Compare

2 event, as mentioned before, mimics a Capture 1 event. This sets the ICF1 bit in the TASR

ware as explained for Input Capture.

The physical Capture 1 input, ICAP1_A, is inhibited for this reason, but the other input pin,

ICAP2_A remains active. This allows input captures to be performed while the timer is used in

Pulse-Width Modulation mode. An example of this is given in the first application in Chapter 9.

In this application, the timer generates periodic pulses while its frequency is controlled using a

Phase-Locked Loop scheme to synchronize it with an external reference frequency.

The application described in Chapter 9 uses the timer in PWM mode with interrupt generation.

The capture feature is also used at the same time to synchronize pulse generation with an ex-

ternal signal, using a Phase-Locked Loop. Another timer is used to produce an interrupt after

a delay each time the timer is reinitialized for the program's needs.

5.6 ANALOG TO DIGITAL CONVERTER

5.6.1 Description

As a measuring device, the converter is specified by parameters that give the degree of accu-

racy of the conversion. These are:

Input range: positive. Negative voltages are not converted.

Type of conversion: ratiometric.

Resolution: 8 bits, that is, 256 discrete values.

Linearity: the conversion is guaranteed monotonic. This means that when the input voltage

increases, the converted value either remains the same or increases, never decreases. The

same applies when the voltage decreases.

Accuracy: to within 1 LSB worst case, all causes of error included; typical 0.3 LSB. This

means that for any voltage at the input, the conversion result does not differ from the

expected result by more than 1/255 of the supply voltage in the worst case, or 0.12%

typically.

Содержание ST7 Series






























































































































































































































































































































Результаты поиска

Содержание ST7 Series

Отзывы:

Похожие инструкции для ST7 Series

Бренды по названию

Популярные бренды

ST ST7 Series, Руководство пользователя

Результаты поиска

Содержание ST7 Series

Отзывы:

Похожие инструкции для ST7 Series

Бренды по названию

Популярные бренды