manualshive.com logo in svg

ST ST10F276E, Руководство пользователя, Страница: 511 / 564

Поделиться
Скачать
ST ST10F276E Скачать руководство пользователя страница 511

DocID13284 Rev 2

511/564

UM0404

Power reduction modes

from ST10F276 Core (active low signal) is low enough to be recognized as a logic “0” by the 
RAM interface (due to V

18

 lower than V

18SB

): the bus status could contain a valid address 

for the RAM and an unwanted data corruption could occur. For this reason, an extra 
interface, powered by the switched supply, is used to prevent the RAM from this kind of 
potential corruption mechanism. 

WARNING:

During Power-Off phase, it is important that the external hardware maintains a stable 
ground level on RSTIN pin, without any glitch, in order to avoid spurious exiting from reset 
status with unstable power supply.

24.3.2 

Exiting stand-by mode

After the system has entered the Stand-by Mode, the procedure to exit this mode consists of 
a standard Power-On sequence, with the only difference that the RAM is already powered 
through V

18SB

 internal reference (derived from V

STBY

 pin external voltage). 

It is recommended to held the device under RESET (RSTIN pin forced low) until external 
V

DD 

voltage pin is stable. Even though, at the very beginning of the Power-On phase, the 

device is maintained under reset by the internal low voltage detector circuit (implemented 
inside the main voltage regulator) till the internal V

18

 becomes higher than about 1.0V, 

there 

is no warranty that the device stays under reset status if RSTIN is at high level during 
power ramp up. So, it is important the external hardware is able to guarantee a stable 
ground level on RSTIN along the Power-On phase, without any temporary glitch.

The external hardware should be responsible to drive low the RSTIN pin until the V

DD

 is 

stable, even though the internal LVD is active. Besides, it is requested an additional time (at 
least 1ms) to allow internal voltage regulator stabilization before releasing the RSTIN pin: 
this is necessary since the internal Flash has to begin its initialization phase (starting when 
RSTIN pin is released) with an already stable V

18

.

Once the internal Reset signal goes low, the RAM (still frozen) power supply is switched to 
the main V

18

. 

At this time, everything becomes stable, and the execution of the initialization routines can 
start: XRAM2EN bit can be set, enabling the RAM.

24.3.3 Real 

time 

clock and stand-by mode

When Stand-by mode is entered (turning off the main supply V

DD

), the Real Time Clock 

counting can be maintained running in case the on-chip low-power oscillator is used to 
provide the reference to the counter. This is not possible if the main oscillator is used as 
reference for the counter: being the main oscillator powered by V

DD

, once this is switched 

off, the oscillator is stopped.

24.4 Output 

pin 

status

During idle mode

 the CPU clocks are turned off, while all peripherals continue their 

operation in the normal way. Therefore all ports pins, which are configured as general 
purpose output pins, output the last data value which was written to their port output latches. 
If the alternate output function of a port pin is used by a peripheral, the state of the pin is 
determined by the operation of the peripheral. Port pins which are used for bus control 
functions go into that state which represents the inactive state of the respective function 

Содержание ST10F276E





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов