ST Group PIRANHA ST 500 Скачать руководство пользователя страница 18

Страница: 18 / 88

ST 500 "Piranha" Operation Manual: Selective HF Detector Channel

In fig.12:

1  -  active detection channel
2  -  signal level at the selected frequency (at cursor position)
3  -  "SET "0"

active

4 - selected passband (1 MHz or 20 MHz)
5 - OSCILLOSCOPE

active

Functionality:



tuning to the frequency of the detected signal



passband selection (1 MHz or 20 MHz);



listening to a demodulated signal



analyzing the signal with oscilloscope



locating the signal source with power method

Controls:

Key

Action

MODE

switching to the main menu of device

ENTER, ESC

turning off "FIXED FREQUENCY ANALYSIS " function

screen cursor positioning

turning on/off "SET "0" function

passband

selection (1 MHz or 20 MHz)

turning on OSCILLOSCOPE

turning on/off gain setting

FUNC

disabled

To turn off "FIXED-FREQUENCY MONITORING" function, press "ENTER" or "ESC". The device

will switch back to the mode, from which the function was activated ("PANORAMA" or
DIFFERENTIAL mode).

3.2.2. "SET "0" FUNCTION

This function helps locate the source of a detected signal. It can be especially helpful in finding

the sources of powerful signals that make the screen levels go off-scale even at minimum gain.
Ways of locating eavesdropping devices are described in more detail in

9.1.4.

When "SET "0" is used, the signal level at current frequency is set as "0", and only the level

differences are displayed.

To turn on the "SET "0", press "F1". The "F1" key field will become lighter.

When using the "SET "0" function, it is possible to:



change the passband ("F2")



turn on the oscilloscope ("F3")



change the gain ("F4")

To turn off the "SET "0", press "F1" again. The "F1" field will become darker.

Содержание PIRANHA ST 500

























































































Результаты поиска

Содержание PIRANHA ST 500

Отзывы:

Похожие инструкции для PIRANHA ST 500

Бренды по названию

Популярные бренды

ST Group PIRANHA ST 500, Руководство пользователя

Результаты поиска

Содержание PIRANHA ST 500

Отзывы:

Похожие инструкции для PIRANHA ST 500

Бренды по названию

Популярные бренды