SPX Waukesha Cherry-Burrell Votator II Скачать руководство пользователя страница 28

Страница: 28 / 84

Installation

Waukesha Cherry-Burrell

Page 28

95-03057

October 2005

4. Check hydraulic pump pressure by moving hydraulic

lift foot away from Votator II unit and running

cylinder in the full up, dead head position. At this

point, it should be adjusted for a gauge reading of 300

to 400 psig at the pump.

5. The pump pressure control (See Figure 17, Item A)

should be set to approximately 4-1/2 turns open in the

counterclockwise direction from the closed position.

This adjustment controls the system pressure and is at

maximum when the setscrew is in the closed or full

clockwise position. It is adjusted by a 3/16" Allen

Head set screw and locked by a 9/16" jam nut.

Gravity Refrigeration System -

Vertical Votator II

The Gravity Refrigeration System includes the following

items that must be installed:

•

Accumulator

•

Media piping

•

Valves

The accumulator, refrigeration piping, and valves are

shipped loose for field installation, as shown in the

drawing titled Vertical Refrigeration System located in the

addendum section and Votator II Vertical Refrigeration

System drawing on page 20 showing the Process Flow

Diagram of the Vertical Refrigeration System. It is

necessary for on-site installation of these components to

insure that the refrigeration system will mate properly with

the Votator II cylinders.

A crane, or other lift device, is needed to lift the

accumulator mounting bracket in place for installation.

Lift the mounting bracket in place with a sling. Bolt the

accumulator to the pole.

To simplify installation, piping is provided in three

modules:

•

the accumulator to the lower manifold

•

the lower manifold to the cylinder flange

•

the upper manifold to the accumulator

Also included are an elbow for the top of the accumulator

and piping legs for connecting the modules.

The refrigeration valves and level control are packed and

shipped separately. These components and the piping

sections should be installed in accordance with the

referenced drawings. A leak test MUST be performed

after all welding is complete.

After a leak test has been successfully completed, the

system piping should be coated with a paint formulated for

corrosion resistance.

Figure 17 - Pressure Adjustment Screw

Содержание Waukesha Cherry-Burrell Votator II





















































































Результаты поиска

Содержание Waukesha Cherry-Burrell Votator II

Отзывы:

Похожие инструкции для Waukesha Cherry-Burrell Votator II

Бренды по названию

Популярные бренды

SPX Waukesha Cherry-Burrell Votator II, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Waukesha Cherry-Burrell Votator II

Отзывы:

Похожие инструкции для Waukesha Cherry-Burrell Votator II

Бренды по названию

Популярные бренды