Spectris 04416001A Скачать руководство пользователя

Страница: 42 / 124

SERVO

PRO NANOCHROME Gas Analyser

04416001A / Revision 7

4.3.3 Injection Mode

Use the

Injection Mode

radio control to select one of two injection modes. The

Manual

mode executes one cycle after the

Start

button is pressed. The

Automatic

mode restarts new cycles until the

Stop

button is pressed or the

Manual

mode is selected.

4.3.4 Injection Status

The

Injection Status

radio control enables sample injection when the

radio

control is selected and disables sample injection when the

OFF

radio control is

selected.

4.3.5 Historic values (F3)

Displays the last 20 measures of concentration for the selected impurity. Select
a peak in the upper-left grid of the

REAL-TIME CHROMATOGRAM

MENU

and then press the

Historic Values (F3)

button to see these values.

4.3.6 Historic Alarm (F4)

Press the

Historic Alarm

button to access the

Historic Alarm

menu. This

button will turn red when an alarm occurs, turn yellow when the menu is
opened and alarms are still active, and turn green if the problem is resolved.
The

Historic Alarm Menu

is described in more detail in section 4.4.

4.3.7 Range (F5)

Use the

CONFIGURATION-SYSTEM MENU

to select either

Manual

Automatic

ranging. If

Manual

ranging is selected, press the

Range

button to

toggle between the 2 ranges. The range used for the last integration of a peak or
the range selected is displayed in the

column, next to the peak value in the

grid at the left of the chromatogram.

To change a peak range set the

Manual

ranging by highlighting the

corresponding peak in the grid and then press the

Range

button.

The

Range

cannot be changed during a peak integration. When

Automatic

ranging is selected, range selection will be automatically

based on the result of the last peak calculations.

Note that when calibration is enabled,

“

Warning: Calibration enabled

”

will be

displayed in the chromatogram display.

Содержание 04416001A





























































































































Результаты поиска

Содержание 04416001A

Отзывы:

Похожие инструкции для 04416001A

Бренды по названию

Популярные бренды

Spectris 04416001A, Руководство оператора

Результаты поиска

Содержание 04416001A

Отзывы:

Похожие инструкции для 04416001A

Бренды по названию

Популярные бренды