Главная
/
Spectris
/
04416001A
/
Руководство оператора

Spectris 04416001A, Руководство оператора

Поделиться

96 страниц до
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124

Страница: 111 / 124

background image

SERVO

PRO NANOCHROME Gas

Analyser

110

04416001A / Revision 7

7 START-UP AND SHUTDOWN PROCEDURE

7.1 Equipment/Tools

1.

Flow meter 0-500 cc/min range with 1 cc/min resolution (Restek ProFlow 6000
Cat#: 22656)

2.

7/16’’ spanner

3.

1/8 VCR gaskets

4.

Helium leak detector (eg Restek Electronic Leak Detector Cat# 22655)

5.

0-100 PSIG Pressure gauge with 1.5% accuracy

7.2 Installation requirements

1.

Face seal fittings (VCR type)

2.

Carrier gas: purified 5N argon or helium

3.

Semiconductor grade 316L stainless steel pipes

4.

All systems parts (valves, fittings, pressure regulators) must be UHP rated

7.3 Start-up procedure

WARNING

Do not connect gas to analyser unless all caps are removed.

Do not pressurise detector vent(s)

The carrier gas must be connected to the analyser before power is

applied

1.

Verify main voltage rating.

2.

Connect carrier gas purifier and follow installation instructions.

3.

Purge the carrier gas line before connecting to the analyser. Static purges are
recommended to fully purge dead volumes. A static purge consists of lowering the
delivery pressure close to atmospheric pressure and re-pressurising to operating
pressure. This process must be repeated at least 5 times.

4.

Remove all caps from the analyser backplate.

5.

Adjust carrier gas supply pressure to 80 psig if sample background gas is He, H2,
N2, Ar or 85 psig if sample background gas is O2. See label on back of analyser.

6.

Connect carrier gas to the analyser.

7.

Connect the process gas to sample inlet 1 and adjust supply pressure to 30 psig.

«
...
109
110
111
112
113
...
»

Содержание 04416001A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 04416001A

Бренд: YOKOGAWA Страницы: 3

Бренд: D-tect Systems Страницы: 19

Бренд: Roland Страницы: 15

Бренд: AEMC Страницы: 4

BUCKMASTERS 1500

Бренд: Sig Sauer Страницы: 2

Combo meter P700 Pro

Бренд: AquaMaster Страницы: 20

Бренд: Cable Ferret Страницы: 16

Бренд: sewerin Страницы: 80

Бренд: YOKOGAWA Страницы: 63

Бренд: Fluke Страницы: 2

Superstatic 749

Бренд: Sontex Страницы: 24

Бренд: M-system Страницы: 8

Бренд: GREISINGER Страницы: 16

Бренд: INTERSPIRO Страницы: 32

Бренд: SDT Страницы: 2

Бренд: netAlly Страницы: 2

Бренд: Metrohm Страницы: 163

Бренд: Ruide Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды