Spectris 04416001A Скачать руководство пользователя

Страница: 13 / 124

SERVO

PRO NANOCHROME Gas Analyser

04416001A / Revision 7

1.4 Description of Analyser Rear Connections

1.4.1 SERVOPRO NanoChrome Complete Rear Connector

Figure 1 : SERVOPRO NanoChrome complete rear connections

This rear panel is fitted to the master chassis, and to the secondary chassis in a
system with a stand-alone PC.

Power inlet with switch and fuse

Gas trap inlet

RS-232 /RS-485 socket

Auxiliary oven

RS-485 socket

Gas trap outlet

Ethernet port

USB port

Analogue 4-20 mA outputs

10.

Digital outputs

11.

Digital input

12.

Earth terminals for cable screens

13.

Carrier gas inlet to detector 1

14.

Carrier gas inlet to detector 2

15.

Vent for carrier gases

16.

Detector 1 vent

17.

Detector 2 vent

18.

Detector 3 vent

19.

Supporting gas inlet

20.

Sample gas vent

21.

Sample gas inlet 1 (process)

22.

Sample gas inlet 2 (span)

Several of the ports shown above are optional, and may be fitted depending on
the analyser configuration and intended use. VCR fittings are used on all gas
inlets, Swagelock (SWG) fittings are used on all gas outlets/vents.

Содержание 04416001A





























































































































Результаты поиска

Содержание 04416001A

Отзывы:

Похожие инструкции для 04416001A

Бренды по названию

Популярные бренды

Spectris 04416001A, Руководство оператора

Результаты поиска

Содержание 04416001A

Отзывы:

Похожие инструкции для 04416001A

Бренды по названию

Популярные бренды