SpectraLink 80-Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 79

SpectraLink 80-Series Скачать руководство пользователя страница 29

Spectralink 80-Series Handsets Administration Guide with SRP

1725-86030-000_G.docx
October 2013

29

ELP Port

Allows the user to select the port number which ELP updates get sent to at the

Location Server IP address. It must match the value configured in the Ekahau Positioning
Engine for proper functionality. The ELP port number must be greater than zero and less than
65536. Default is 8552. Enter the port number and press

NavOK

to save.

Network Config

IP Address

There are two modes in which the handset can operate: DHCP enabled or Static IP. Select the
mode for operation from the IP address menu:

* Use DHCP

Will use DHCP to assign an IP address each time the handset is turned on. If

DHCP is enabled, the handset also receives all other IP address configurations from the DHCP
server.

Static IP

Allows you to manually set a fixed IP address. If selected, the handset will prompt for

the IP addresses for each configurable network component. When entering addresses, enter
the digits only, including leading zeroes. Do not enter punctuation.

Regardless of the mode in which the handset is operating, the following components must be
configured:

Phone IP

The IP address of the handset. This is automatically assigned if DHCP is used. If

using Static IP configuration, you must obtain a unique IP address for each handset from your
network administrator.

Default Gateway and Subnet Mask

Used to identify subnets, when using a complex network

which includes routers. Both of these must be configured either with an IP address under Static
IP (not set to 000.000.000.000 or 255.255.255.255) or with DHCP for the handset to contact any
network components on a different subnet. If configured on the DHCP server, use option 3 for
the Default Gateway and option 1 for the Subnet Mask. Contact your network administrator for
the proper settings for your network.

«
...
27
28
29
30
31
...
»

Содержание 80-Series
















































































Отзывы:

Нет отзывов