Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 90

background image

77

MPC 5000 FUSES

The CHECK FUSE alarm indicates that one of the seven fuses on the MPC-5000 Printed Circuit
Board has blown. These fuses are the flat, color-coded, small ATM automotive style. The dis-
play will indicate by number which fuse has blown, and the fuse bases are numbered on the
board. Before replacing the fuse, find and repair the problem that caused the fuse to blow.
The fuses supply power to the terminal strip on the PCB as follows:

Fuse F1 (5 Amp):

PVLV Priming valve solenoid

FWV Fresh water flush valve solenoid

Fuse F2 (5 Amp):

AUX 3. Optional boost pump

Fuse F3 (10 Amp):

PMP1, Feed pump number 1

Fuse F4 (5 Amp):

DVLV, Diversion valve solenoid

Fuse F5 (10 Amp):

PMP 2, Feed pump number 2

Fuse F6 (10 Amp):

AUX 1, Powered when display illuminated

AUX 2, Powered during run cycle

Fuse F7 (5 Amp):

STER, Powered when feed pump running. Optional ultraviolet

sterilizer.

Before replacing fuses, shut off the main power supplies. Remove the lead wire that goes to
the affected component from the terminal strip. Using a digital ohmmeter, check the circuits
for dead shorts. You should see about 10 ohms or more on the solenoid valve circuits.

MCP 5000 Electrical Specifications

Operating voltage limits:

11.6 – 13.8 for 12-volt systems, 23.2 – 27.6 for 24-volt systems

Controller power consumption, mAmp – 700 maximum

Outputs:

BUZZ – 100 mA DC Piezo buzzer.

PVLV – 2.5 Amp DC priming valve solenoid.
FWV – 2.5 Amp DC fresh water valve solenoid.

AUX3 – 5 Amp DC auxiliary output.

PMP1 – 15 Amp DC auxiliary water feed pump.
DVLV – 10 Amp DC diversion valve solenoid, modulated at 17% duty cy-
cle after 2.5 seconds to reduce power consumption.
PMP2 - 15 Amp DC main water feed pump.
AUX1 - 2.5 Amp DC auxiliary output.
AUX2 – 2.5 Amp DC auxiliary output.
STER – 5 Amp DC sterilizer.

«
...
75
76
77
78
79
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

Multipur M DN100

Бренд: BWT Страницы: 36

Бренд: SMC Networks Страницы: 32

Бренд: 3M Страницы: 36

Бренд: Aqua Free Страницы: 2

Бренд: DAB Страницы: 228

Бренд: Econ Страницы: 7

Бренд: SANUSLIFE Страницы: 10

Бренд: Nilfisk-Advance Страницы: 84

Бренд: KYOKUTOH Страницы: 12

Бренд: Water Control Страницы: 20

Бренд: 3P Technik Страницы: 2

Бренд: Ispring Страницы: 2

BlueSoft-10-SVR34

Бренд: Euro-Clear Страницы: 20

AQUAJOE SJI-OMS18-RM

Бренд: SNOWJOE Страницы: 8

Бренд: Austin Springs Страницы: 5

President Series

Бренд: Graco Страницы: 22

Бренд: Super Страницы: 13

Бренд: Super Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды