Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 90

background image

74

INLET OFFSET: This parameter calibrates the boost pressure sensor found on the intake manifold
of the feed pump (marked yellow). The number on the left is the real time pressure reading and
the number on the right is the offset. The reading can be increased or decreased by putting a posi-
tive or negative number in the offset setting.

OUTLET OFFSET: Outlet Offset calibrates the sensor on the outlet of the feed pump which is used
to determine feed pressure (marked red). The number on the left is the real time pressure reading
and the number on the right is the Offset in PSI or bar.

BRIGHTNESS: The brightness may be adjusted from 0 to 4. Factory default is 0.

FLUSH DURATION: This parameter sets the length of the fresh water flush in minutes. Factory
default is 6.

PUMP ON TIME: Sets the length of time, in seconds, that the feed pump will cycle on during a
fresh water flush. Factory default is 360.

PUMP OFF TIME: Sets the time in seconds that the flush valve is open, but the feed pump is not
running. Factory default is 0.

FLUSH INTERVAL: This is the time in days between automatic flushes when the system is in Auto
Store mode. The Flush Interval is programmed in days, but the Flush Interval Timer will count
down in hours. Factory default is 5 days; 30 days with the optional Z-Ion.

CLEAN PRESSURE: This should be set to one whole number below the pressure seen at the inlet
sensor when the system is running with a brand new pre-filter. After installing a new filter, run the
machine by flipping the toggle switch on the MPC box to RUN MAN. The number on the right is
adjusted to be one whole number below the number on the left, which is the inlet sensor reading.
This parameter sets the “Clean” end if the pre-filter condition bar graph. Factory default is 15.

MPC 5000 Software may be loaded from www.spectrawatermakers.com or CD ROM, and in-
stalled on most Windows-based computers. The computer must then connect to the MPC board
with a USB cable with a type B connector on one end, as shown. Due to wide variations in comput-
ers and operation systems, Spectra cannot provide installation support, and we only recommend
this software for experience technicians. All parameters and programming can be easily accessed
from the MPC display, without this software.

Type B connector plugged
into MPC circuit board

«
...
72
73
74
75
76
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

Бренд: GE Страницы: 2

Profile PNRQ15FBL

Бренд: GE Страницы: 2

Бренд: GE Страницы: 24

Бренд: GE Страницы: 36

Бренд: GE Страницы: 16

Бренд: CAB Страницы: 15

Бренд: Galletti Страницы: 8

Бренд: Survivor Filter Страницы: 7

Бренд: Deltec Страницы: 7

Бренд: Tecno-gaz Страницы: 122

HiFlo Ro-Moobil RO60S

Бренд: unGer Страницы: 16

Бренд: Exhausto Страницы: 32

Бренд: Watts Страницы: 38

Бренд: Bartscher Страницы: 8

SuperFish X-Pro 1000

Бренд: Aquadistri Страницы: 12

Spirocombi BA Series

Бренд: Spirotech Страницы: 28

Бренд: MANN+HUMMEL Страницы: 9

Бренд: GE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды