Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 90

background image

19

Plumbing Detail

Your system includes 25-feet of 1/2-inch vinyl hose with a Quick
Connect fitting on one end and a 1/2-inch John Guest stem
fitting on the other, both crimped on with ferrules. You will CUT
THIS HOSE and, using the fittings found in the installation kit,
use one end for the feed water inlet hose and the other for
the fresh water flush hose:

Fresh Water Flush: Route a feed line from the domestic cold pressure water system to the
1/2-inch hose barb on the fresh water flush module. This needs to be pressurized when the
boat is unattended for the fresh water flush system to function properly.

The domestic fresh

water pump must be able to deliver 1.5 gallons per minute (6 LPM) at 25 PSI (1.7 bar).

Attaching 1/2-inch vinyl hose to sea
strainer using the 3/8” John Guest
stem fitting and hose clamp found in
installation kit:

Attaching 1/2-inch vinyl hose to Z-Ion/
fresh water flush module with the pre-
fitted Quick Connect fitting:

Flush water from ship’s
pressure water system
25 psi (2bar) minimum

The optional Z-ION will re-

place the Fresh Water

Flush module

From the intake sea cock to the sea strainer/boost pump module,
and from the sea strainer/boost pump module to the pre-filter
housing on the feed pump module, use the 3/4-inch black, spiral-
wound suction hose:

«
...
17
18
19
20
21
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

SmartWater GX1S01C

Бренд: GE Страницы: 2

Бренд: GE Страницы: 20

Бренд: GE Страницы: 36

Бренд: NatureWater Страницы: 16

HydroPower RO35C

Бренд: unGer Страницы: 32

Бренд: Hunter Страницы: 2

Бренд: Waterdrop Страницы: 28

Бренд: ITech Страницы: 14

Бренд: SpringWell Страницы: 23

Бренд: MANN+HUMMEL Страницы: 9

Coffee Lovers System CLS-5-90

Бренд: SpectraPure Страницы: 24

Бренд: Unimec Страницы: 32

Бренд: SpectraPure Страницы: 24

Бренд: SYR Страницы: 16

Бренд: NuAire Страницы: 7

Бренд: KineticoPRO Страницы: 2

Бренд: DriSteem Страницы: 16

Бренд: CPI Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды