Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 90

background image

49

The Feed Pump and Clark Pump

The feed pump and the Clark Pump require no routine maintenance except inspection for
leaks. Tighten any hose clamps or fittings that show signs of leakage. The high pressure fittings
threaded into the Clark Pump have O-ring seals with a straight thread. These should never leak
and should never be over-tightened. If one of the tube nuts starts to leak, it can be un-
threaded, sealed with a bit of silicone grease or oil, and tightened with two wrenches very
tightly. See instructions on page 23.

The Membrane

Always perform a flow test (page 60) before cleaning your membrane. Cleaning is hard on
membranes, so only clean a membrane if you have ruled out other possibilities for low pro-
duction or poor water quality. The leading cause of fouling is biological growth that forms
when the system is left unused without flushing or pickling. Fouling from mineral scaling can
happen under certain seawater conditions, or from rust. Monitor the product salinity and feed
pressure for higher than normal readings, take environmental conditions into consideration:



Cold feed water can cause high pressure.



Low product flow is usually due to low voltage, a worn feed pump, or worn Clark Pump.

Test to see if biological growth has occurred: Before running the system, remove the prefil-
ter and examine its condition. If the filter housings are full of smelly, discolored water, the sys-
tem was not properly stored. Install a clean pre-filter.

Next check the membrane. Detach the brine discharge hose, attach the brine service hose, and
lead it to a bucket. Open the pressure relief valve 1/2 turn, and manually run the system for 30
seconds (metal toggle switch on feed pump module). Examine the brine water: If it is discol-
ored and smells bad, perform an SC-2 cleaning with unchlorinated water before running the
system pressurized. If the brine is fairly clean, follow the New System Startup procedure on
page 41 and run normally. Check for performance. Clean the membranes only if performance
is reduced.

See the Cleaning Procedure on page 56 for complete instructions.

Maintenance continued...

«
...
47
48
49
50
51
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

Kaysun Aquantia R-32 PRO

Бренд: Frigicoll Страницы: 44

Бренд: TCi Страницы: 61

Бренд: Deltec Страницы: 16

FLECK 5800 XTR2

Бренд: Aquaox Страницы: 7

7200/1 170 Plus

Бренд: Riello Страницы: 16

Бренд: WaterChef Страницы: 8

Wafergard III NF-750

Бренд: entegris Страницы: 7

Бренд: Viking Страницы: 13

CRITI-CLEAN ULTRA Series

Бренд: AJ Страницы: 30

Pantera PCFII-075

Бренд: onga Страницы: 16

Бренд: Laica Страницы: 2

Бренд: Baxi Страницы: 6

USRO4-100-QC-38

Бренд: H20 Distributors Страницы: 9

Бренд: Aqua Optima Страницы: 2

Бренд: Aqua Perfecta Страницы: 12

Nautilus 2700UVC

Бренд: Aqua One Страницы: 16

Бренд: K-Rain Страницы: 2

ClearSolution 120800

Бренд: ThePondguy Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды