Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 90

background image

53

Winterizing with Propylene Glycol

See description of propylene glycol formulations, and flushing from system, on page 52-53.

1.  Close the intake seacock.
2.  Push Auto Store to fresh water flush the system. Repeat, to flush the system twice.
3.  Remove the fresh water flush hose from the fresh water flush module or Z-Ion at the Quick

Connect fitting, connect the intake service hose, and lead it into a bucket. Connect the brine
service hose, and run it into a second container.

4. Pour 1 gallon (4 liters) of propylene glycol of appropriate concentration (see pages 52-53) into

the bucket with the intake service hose.

5. Make sure the pressure relief valve on the Clark Pump is OPEN 1/2 turn (un-pressurized).
6. Run the feed pump using the SERVICE setting on the manual toggle switch until about a gallon

of water has flowed from the brine discharge service hose, or antifreeze appears. Propylene
glycol will look slightly different, and feel more slippery, than water. Return the switch to RUN
AUTO to stop the pump. Add more propylene glycol to the intake bucket if necessary.

7. Lead the brine discharge service hose into the same bucket as the intake service hose. The ser-

vice hose will now draw propylene glycol solution from the bucket, and the brine discharge
service hose will return it. Run the feed pump on the SERVICE setting and circulate the propyl-
ene glycol solution for 10 minutes.

8. Stop the feed pump by returning the switch to RUN AUTO. Remove the service hoses. Discon-

nect the product tubing from the membrane housing and blow residual water out of the tub-
ing. Empty the charcoal filter housing and flush water lines.

Your watermaker is now protected from biological growth and freezing for one year.

Toggle switch set to SERVICE

Connecting brine discharge service
hose

Connecting intake service hose

Open the Pressure Relief Valve

«
...
51
52
53
54
55
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

Бренд: Ace Страницы: 13

Бренд: Danfoss Страницы: 94

Бренд: Hach Страницы: 4

Бренд: H2oLabs Страницы: 16

Elite HydroTap G4 range

Бренд: Zip Страницы: 20

RainStation RS-0001

Бренд: EarthMinded Страницы: 16

AQUAGUARD CREST UV +HOT

Бренд: Eureka Forbes Страницы: 13

Hydro-Guard HG-4

Бренд: Mueller Страницы: 8

Бренд: PAPILLON Страницы: 8

4 Stage Barracuda RO/DI

Бренд: AquaFX Страницы: 11

Бренд: Watts Страницы: 20

Бренд: Keating Of Chicago Страницы: 2

300-H-4510-BG-222-KIT

Бренд: US Water Systems Страницы: 17

Aquajoe SJI-TLS18

Бренд: SNOWJOE Страницы: 12

Бренд: Waterco Страницы: 12

Бренд: Culligan Страницы: 6

CHV5 Home HWC16NK

Бренд: Cooper&Hunter Страницы: 19

Бренд: Waterco Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды