Spectra Watermakers Catalina 340 Z Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 90

background image

52

Catalina 340 Z Storage Procedure

1.  Close the intake seacock.
2.  Push Auto Store to fresh water flush the system. Repeat, to flush the system twice.
3.  Remove the quick disconnect fitting from the brine discharge outlet of the Clark Pump, and

replace it with the quick disconnect brine discharge service hose. Lead the brine discharge
service hose into a 5-gallon (20 liter) bucket. Push the Auto Store button and run the feed
pump until you have one gallon of fresh water in the bucket from the brine discharge ser-
vice hose. Press Stop to stop the system.

4. Remove the fresh water flush hose from the fresh water flush module or Z-Ion at the Quick

Connect fitting, connect the intake service hose, and lead it into the bucket.

5. Mix 1 container of SC-1 storage compound with the water in

the bucket.

6. Make sure the pressure relief valve on the Clark Pump is

OPEN (un-pressurized) by turning 1/2 turn counterclockwise.

7. Flip the toggle switch on the feed pump module to the SER-

VICE setting. The solution will be drawn from the bucket with
the intake service hose, and returned to the bucket from the
brine discharge service hose. Circulate the storage chemical in
this manner for approximately 10 minutes. Return the toggle switch to the RUN AUTO po-
sition to stop.

Clean Up

Remove the brine discharge service hose from the Clark Pump, and replace the brine dis-
charge hose that leads to the thru-hull. You may now pump the bucket dry by using the manu-
al control switch on the feed pump module.

Remove the inlet service hose and replace the fresh water flush hose at the Quick Connect
fitting. Leave the pressure relief valve open, since the next time you run the system you will
need to purge the storage chemicals with the system unpressurized.

Connecting brine dis-
charge service hose

Toggle switch to SERVICE

Replacing fresh water flush
hose with intake service
hose

«
...
50
51
52
53
54
...
»

Содержание Catalina 340 Z



























































































Отзывы:

Нет отзывов

Похожие инструкции для Catalina 340 Z

Бренд: NaturalSof Страницы: 12

Spray Away 5266

Бренд: Havahart Страницы: 6

Бренд: Aquasana Страницы: 12

Бренд: claber Страницы: 21

Бренд: RoDEK Страницы: 19

Бренд: Pentair Страницы: 12

Бренд: PurePro Страницы: 4

Prestige Close Coupled Systems

Бренд: Rinnai Страницы: 48

AQUA OCEAN AQ4000

Бренд: ICA Страницы: 16

Бренд: Zodiac Страницы: 16

Micromax 6000 TFC

Бренд: Ionics Страницы: 12

Бренд: Jupiter Страницы: 16

CENTRAL TY-B Series

Бренд: Tyco Fire Product Страницы: 6

Бренд: LAMA Страницы: 24

Бренд: O-SO Pure Страницы: 16

Tannin 5900e Series

Бренд: Clean Water Systems Страницы: 22

Бренд: Pall Страницы: 8

Бренд: Pall Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды