background image

8

SEATPOST MINIMUM INSERTION

To prevent damage to the frame or seatpost, it’s crucial 
to have a minimum amount of seatpost inserted in 
the seat tube. This minimum insertion must meet the 
following requirements:

35. 

The seatpost must be inserted into the frame 

deep enough so the minimum insertion/maximum 
extension (min/max) mark, where applicable, on the 

seatpost is not visible 

(A)

.

36. 

The seatpost must also be inserted into the seat 

tube deep enough to meet or exceed 

(B)

 the 

minimum measured insertion depth required by the 

frame 

(C)

.

Refer to the User Manual supplied with 

your bicycle for more specific information 

on the seatpost maximum and minimum 

insertion depths.
WARNING! Failure to follow the outlined 

seatpost insertion requirements may 

result in damage to the frame and/or 

seatpost, which could cause you to lose 

control and fall.

37. 

Using a wrench and corresponding hex bit, loosen 
the seatpost clamp bolt and set the saddle height 
to your desired position, then lightly tighten the 

seatpost clamp bolt.

38. 

Align the saddle with the centerline of the bicycle.

DROPPER SEATPOST: 

While adjusting the 

seat height of your seatpost, push or pull 

the excess dropper cable throught the 

cable port at the front of the bicycle as 

required.

39. 

Using the torque wrench and corresponding hex 
bit, torque the seatpost clamp bolt to the specified 
torque setting found on the seatpost clamp and/or in 

the User Manual.  

Refer to the Owner’s Manual for more 

information on setting up your saddle 

height.

INFLATE THE TIRES

The tires must be inflated and periodically checked 

and re-inflated using a pump with an accurate 

pressure gauge. Because of the extra weight of your 
Turbo e-bike, as a rule of thumb, tire pressure should 
generally be higher compared to a regular bicycle.

40. 

Pump the tires up to your desired pressure. Refer to 

the tires sidewalls for pressure range. Check your 

wheel manual or decal on the rim itself to see if 
your wheels have a maximum pressure limit. Do not 
exceed it.

CK

Refer to the Tires and Tubes section of 

the Specialized Bicycle Owner’s Manual 

for additional information.

WARNING! Never inflate a tire beyond the 

maximum pressure marked on the tire’s 

sidewall or the maximum pressure limit 

specified by the wheel manufacturer, 

whichever is lower. Failure to follow this 

warning may cause the tire to blow off 

the rim and may result in serious personal 

injury. 

C

B

A

35

36

37

38

39

40

Содержание 98122-0001























Отзывы: