Sparkrite SR100 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 20

Sparkrite SR100 Скачать руководство пользователя страница 19

SR100 REMOTE CONTROL CAR ALARM SYSTEM

19

ADDITIONAL REMOTE CONTROL TRANSMITTERS

Available from HALFORDS or from Stadium Consumer Products at the following
address:

STADIUM CONSUMER PRODUCTS

STADIUM NORTH

UNITS 8-11 TOFTS FARM

INDUSTRIAL ESTATE

BRENDA ROAD

HARTLEPOOL

TS25 2DH

TELEPHONE: 01429 862616

QUOTE YOUR SERIAL NUMBER FROM THE REAR OF THE TRANSMITTER OR

THE MAIN ALARM MODULE AND REMEMBER TO SPECIFY THE MODEL OF

THE ALARM.

REMOTE CONTROL SERIAL NO.___________________

TECHNICAL HELP

If you have any problems with the installation of this alarm and the problem cannot
be solved by consulting the troubleshooting section the this manual, either consult
Halfords or contact the Sparkrite Technical and After Sales Service (T.A.S.S).

PRODUCT APPROVALS

Your SR100 has been tested and approved by various governmental bodies to
comply with the latest European directives for E.M.C. and Low power transmission.

Approvals:

EMC European directive 95/54.

Approval No: ell 020042

RA/DTI Low power transmission.

Approval No: 4179 for 418MHz
Approval No: 11835 for 433MHz

MPT 1340 Licence Exempt.

«
...
17
18
19
20
»

Содержание SR100





















Отзывы:

Нет отзывов