manualshive.com logo in svg

Sparkrite SR100, Руководство пользователя, Страница: 15 / 20

Поделиться
Скачать
Sparkrite SR100 Скачать руководство пользователя страница 15

SR100 REMOTE CONTROL CAR ALARM SYSTEM

15

NOTE:

Do not set the shock sensor at a higher than necessary
setting otherwise false alarms will occur. If a bonnet
switch is fitted, ensure the switch is held closed position
(or disconnected) to eliminate the circuit whilst adjusting
this feature finally replace the blanking plug.

TESTING THE ALARM INSTALLATION

1)

check all connections are secure and the vehicle battery is connected.

2)

Ensure the car ignition is turned off.

3)

Press the remote control button. The alarm will disarm with one chirp and
one flash of the indicators.

4)

Press the remote control button. The alarm will disarm with two chirps and
two flashes of the indicators.

5)

Arm the alarm. Wait approximately 20 seconds, open a door ensuring interior
light operates. The alarm will trigger. Disarm the alarm. (Refer to trouble
shooting section if alarm fails to trigger).

6)

Repeat the arming procedure and trigger via shock sensor. Disarm alarm.

7)

Repeat the arming procedure and trigger the alarm by opening the door.
Alarm will sound. Now attempt to start vehicle (Vehicle starter motor should
NOT operate whilst the Alarm Siren is sounding).

8)

Test remote panic features by holding down the remote control button for 3
seconds. The alarm will trigger.

Release button and press again to disarm

the alarm. If problems are encountered, refer to trouble shooting guide before
proceeding further. Once the alarm has been successfully tested you may
now secure the ultrasonic unit in place.

:

Complete the installation by securing all wiring and the main ultrasonic control unit
neatly.

IMPORTANT

Finally ensure that all wiring is neatly secured/insulated where necessary and fuses
etc. are checked for safety.
Install the window warning labels on the drivers and passenger windows and make a
note of your remote control serial number in the space provided on page 22.

Содержание SR100





















Отзывы:

Нет отзывов